AESL Airtourer

Victa Airtourer
AESL Airtourer 100/A1 inflight near Shepparton Airport
Role Light utility aircraft
Manufacturer Victa Ltd
Designer Henry Millicer
First flight 31 March 1959 (100)
17 September 1962 (115)
September 1968 (150)
November 1968 (Super 150)[1]
Introduction 1962 (100)
1963 (115)
Produced 1962-1966 (100 and 115, Victa)
1967-1973 (115 and 150, AESL)[1]
Number built 168 (Aust); 80 (NZ)
Variants Victa Aircruiser

The Victa Airtourer is an all-metal light low-wing monoplane touring aircraft that was developed in Australia, and was manufactured in both Australia and New Zealand.

Design and development

The Airtourer was the winning design, submitted by Henry Millicer, the chief aerodynamicist of Australia's Government Aircraft Factories,[1] in a competition organised by Britain's Royal Aero Club in 1953.[2] A wooden prototype was constructed by a small group of enthusiasts (the Air Tourer Group of the Australian Ultra Light Aircraft Association)[1] in the Melbourne suburb of Williamstown during the late 1950s. This prototype, registered VH-FMM[3] (nicknamed Foxtrot Mickey Mouse) was first flown on 31 March 1959 by Flt. Lt.Randell Brown at Moorabbin airport.[1]

The Airtourer design is of cantilever low-wing monoplane configuration, with a fixed tricycle landing gear. It has interconnected ailerons and flaps, with both systems functioning as both ailerons and as flaps when operated. The nosewheel was steerable. Space was available for luggage (45 kg weight limit).[1]

The prototype[4] was demonstrated to aero clubs and flying schools as a possible replacement for existing training aircraft, mostly Tiger Moths and Chipmunks. After trial flights over Melbourne and then to the Latrobe Valley Airport development continued to the all-metal version. The all-metal prototype to production standard (VH-MVA) followed on 12 December 1961.

Interest was shown in the design by Mervyn Richardson, Chairman of Victa Ltd, which at that time was best known for making lawn mowers and light two-stroke engines. Richardson was interested in entering an aviation-related industry. During the period 1961 to 1966, Victa Ltd. undertook production of the all-metal Airtourer, building both 100 hp and 115 hp models. Victa production continued until 1966.

As the Australian Government had rejected Victa’s appeals for tariff protection assistance, and for funding assistance to keep the production lines open, the company had no choice other than to close down its Aviation Division in February 1966, by which time it had built 168 aircraft.

The manufacturing rights to the Airtourer were purchased the following year by the maintenance firm Aero Engine Services Ltd (AESL) in New Zealand where further production of 115 hp and 150 hp models took place until 1973.

Henry Millicer had designed the Victa Aircruiser, a four-seater derivative design, powered by a 210HP Continental O-360 engine, which was certificated in 1967. AESL acquired the rights to the design in 1970 and it was used to form the basis of the CT/4 Airtrainer.

A total of 168 were completed or significantly completed by Victa in Sydney and a further 80 built by AESL in Hamilton NZ. Actually it would be correct to say that 170 serial numbers were issued by Victa and 80 by AESL.

Examination of the records show that some of the late serial numbers issued by Victa were completed in NZ and issued with a NZ serial number (starting at 501). In addition, some of the Victa-built aircraft were rebuilt in the factory by AESL and issued with NZ serial numbers which accounts for some duplication.

AESL delivery pilot Cliff Tait used an Airtourer, ZK-CXU Miss Jacy, for a record breaking flight, circumnavigating the globe between May and August 1969 and covering 53,097 km in 288 flying hours. Miss Jacy is now on display at the MOTAT museum in Auckland

The Australian Certificates of Type Approval for the Victa Air Tourer 100 and 115 are now held by the Airtourer Cooperative Ltd of New South Wales, Australia.[5][6]

Some 90 aircraft remain in Australia with around 20 or so elsewhere, mainly in New Zealand and the United Kingdom.

Variants

AESL produced 7 Airtourers from parts provided by Victa, before launching production of its own aircraft, ultimately produced in 7 different variants:

The T7 was offered as a fixed-pitch T6, but no orders were received for this configuration.

Operators

Military operators

 Thailand
 Tonga

Specifications (Victa Airtourer AT.115)

Data from Jane's All The World's Aircraft 1966–67[7]
Mondey, p. 244[1]

General characteristics

Performance

Gallery

Design notes

VH-MVA was later re-engined and was the first Airtourer 115 around 1963. As for FMM, it is owned by the Museum of Victoria having last been displayed at the Australian Naval Aviation Museum in Nowra, NSW.

The Air Tourer was produced with a 'square hand grip' on the centrally-located control stick.

References

  1. 1 2 3 4 5 6 7 Mondey
  2. ↑ 103 entries were submitted in the 1953 competition. (Mondey)
  3. ↑ VH-FMM
  4. ↑ photograph of prototype
  5. ↑ Certificate of Type Approval No. 34-1 Archived 22 July 2008 at the Wayback Machine.
  6. ↑ Certificate of Type Approval No. 34-3 Archived 22 July 2008 at the Wayback Machine.
  7. ↑ Taylor 1966, pp. 9–10.
  8. ↑ econ. cruise

External links

Wikimedia Commons has media related to AESL Airtourer.
This article is issued from Wikipedia - version of the 11/17/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.