Tetrabromoethane

Tetrabromoethane
Names
IUPAC name
1,1,2,2-Tetrabromoethane[1]
Other names
  • Acetylene tetrabromide[2]
  • Muthmann's liquid
  • Tetrabromoacetylene[2]
  • Symmetrical tetrabromoethane[2]
Identifiers
79-27-6 YesY
3D model (Jmol) Interactive image
Abbreviations TBE[2]
1098321
ChemSpider 6339 N
ECHA InfoCard 100.001.083
EC Number 201-191-5
MeSH 1,1,2,2-tetrabromoethane
PubChem 6588
RTECS number KI8225000
UN number 2504
Properties
C2H2Br4
Molar mass 345.65 g·mol−1
Appearance Colourless liquid
Density 2.967 g mL−1
Melting point −1.0 °C; 30.3 °F; 272.2 K
Boiling point 243.6 °C; 470.4 °F; 516.7 K
630 mg L−1 (at 20 °C)
Vapor pressure 10 Pa (at 20 °C)
1.637
Thermochemistry
165.7 J K−1 mol−1
Hazards
Safety data sheet hells-confetti.com
GHS pictograms
GHS signal word DANGER
H319, H330, H412
P260, P273, P284, P305+351+338, P310
T+
R-phrases R26, R36, R52/53
S-phrases (S1/2), S24, S27, S45
NFPA 704
Flammability code 1: Must be pre-heated before ignition can occur. Flash point over 93 °C (200 °F). E.g., canola oil Health code 3: Short exposure could cause serious temporary or residual injury. E.g., chlorine gas Reactivity code 1: Normally stable, but can become unstable at elevated temperatures and pressures. E.g., calcium Special hazards (white): no codeNFPA 704 four-colored diamond
1
3
1
Flash point 97 °C (207 °F; 370 K)
335 °C (635 °F; 608 K)
Lethal dose or concentration (LD, LC):
  • 1.2 g kg−1 (oral, rat)[3]
  • 5.25 g kg−1 (dermal, rat)
  • 0.4 g/kg (oral, guinea pig)[3]
  • 0.4 g/kg (oral, rabbit)[3]
  • 0.269 g/kg (oral, mouse)[3]
38 ppm (rat, 4 hr)[3]
US health exposure limits (NIOSH):
PEL (Permissible)
 TWA 1 ppm (14 mg/m3)[2]
REL (Recommended)
 None established[2]
IDLH (Immediate danger)
 8 ppm[2]
Related compounds
Related alkanes
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
N verify (what is YesYN ?)
Infobox references

Tetrabromoethane (TBE) is a halogenated hydrocarbon, chemical formula C2H2Br4. Although three bromine atoms may bind to one of the carbon atoms creating 1,1,1,2-tetrabromoethane this is not thermodynamically favorable, so in practice tetrabromoethane is equal to 1,1,2,2-tetrabromoethane, where each carbon atom binds two bromine atoms.

It has an unusually high density for an organic compound, near 3 g/mL, due largely to the four bromine atoms.[4] TBE is a liquid at room temperature, and is used to separate mineral ores from its supporting rock by means of preferential flotation. Sand, limestone, dolomite, and other types of rock material will float on TBE, while minerals such as sphalerite, galena and pyrite will sink. A related compound, bromoform, is also sometimes used in these applications, however, TBE is more practical because of its wider liquid range and lower vapor pressure.[4] Acute TBE poisoning has been known to occur.[5]

References

  1. ↑ "1,1,2,2-tetrabromoethane - Compound Summary". PubChem Compound. USA: National Center for Biotechnology Information. 26 March 2005. Identifiction. Retrieved 20 June 2012.
  2. 1 2 3 4 5 6 7 "NIOSH Pocket Guide to Chemical Hazards #0009". National Institute for Occupational Safety and Health (NIOSH).
  3. 1 2 3 4 5 "Acetylene tetrabromide". Immediately Dangerous to Life and Health. National Institute for Occupational Safety and Health (NIOSH).
  4. 1 2 Organic based heavy liquids, heavyliquids.com
  5. ↑ A B van Haaften (1969). "Acute tetrabromoethane (acetylene tetrabromide) intoxication in man". American Industrial Hygiene Association. 30 (3): 251–256. doi:10.1080/0002889698506042.
This article is issued from Wikipedia - version of the 11/2/2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.