Polish railway signalling

The Polish railway signalling system provides a complex outlook of traffic situations, yet is quite easy to understand. Signals can be divided into following categories:

Most signals are colour lights.

On few stations remained mechanical signals, as well as old colour light signals.

Colour light signals

Semi-automatic signals

Semi-automatic is the most important type of signal on Polish railways. Its name reflects the fact that it switches to a red (stop) aspect automatically after a train has passed it but it must be switched back to clear by an explicit action from a signal box or dispatch centre. It is the typical signal in use at stations.

A semi-automatic signal can be recognized by its post which is painted with red and white strips. Dwarf versions have their boxes painted so.

A red (stop) aspect on a semi-automatic signal must not be passed.

As presented on this compact chart, semi-automatic signals can display both near and distant functions. Near signals either command a stop or impose a certain speed limit beginning at that signal. Distant signals tell the driver what to expect at the next signal, especially when braking is required.

Distant signal
Vmax 100 km/h 60 or 40 km/h Stop unspecified


















Vmax 100 km/h 60 km/h 40 km/h Stop
Near signal
All permitted aspects on semi-automatic signals:





S1 stop
Proceed or speed reduction order:





 S2 clear, proceed at Vmax
S3 reduce speed to 100 km/h
S4 reduce speed to 60 or 40 km/h
S5 stop at next signal
Speed limit 100 km/h:





 S6 speed limit 100; will be Vmax after next signal
S7 speed limit 100; will be 100 after next signal
S8 speed limit 100; will be 60 or 40 after next signal
S9 speed limit 100; will be stop at next signal
Speed limit 60 km/h:





 S10a speed limit 60 km/h; will be Vmax after next signal
S11a speed limit 60 km/h; will be 100 after next signal
S12a speed limit 60 km/h; will be 60 or 40 after next signal
S13a speed limit 60 km/h; will be stop at next signal
Speed limit 40 km/h:





 S10 speed limit 40 km/h; will be Vmax after next signal
S11 speed limit 40 km/h; will be 100 after next signal
S12 speed limit 40 km/h; will be 60 or 40 after next signal
S13 speed limit 40 km/h; will be stop at next signal

Other speeds

Since 2007 the Ie-1 code which regards signalling allows other speed limits. They are indicated by a number representing the speed in tens of km/h (e.g. 5 means 50 km/h) which is lit only with adequate aspect of the signal. These numbers are incorporated into signalling so, that they always loosen the restriction presented by the aspect of signal.

On distant signals and repeaters these other speeds are not displayed, therefore more restrictive aspect is effectively announced.

Nameplates

Semi-automatic signals on a station are tagged with consecutive letters of Latin alphabet, or with a letter followed by a number.

The nameplates also contain speed indication which appears as a superscript or a fraction. The numbers have following meaning:

Therefore, a nameplate H 1/2 means a signal named H that aside S1 will also display S2-S5 aspects for straight direction and S10-S13 for diverging direction. Whereas P3 2 means a signal of name P3 that aside S1 only displays S10-S13 aspects because it is only followed by diverging direction.

There may also be a letter m which specifies that this signal also functions as a shunting signal (see below).

Subsidiary signal

Subsidiary Signal





Sz, the subsidiary signal (Pol. sygnał zastępczy) is a signal issued in case of malfunction.

The first picture presents a typical case where the dispatcher cannot change the signal from S1.
The second picture presents a case where the signal is powered down.
Third picture presents a special signal where only the Sz sign can be displayed. The train must stop and wait until Sz is issued.

Automatic signals

Automatic signals are used on lines equipped with automatic block signaling. Their colour language is the same as aspects S1-S5 of semi-automatic signals. The main difference regards the S1 (red) aspect - After stopping, it can be passed but the subsequent maximum speed is limited to 20 km/h.

Automatic signals have their posts painted white (without red strips) to be easily distinguished from semi-automatic signals.

Automatic signals:
2-state ABS:

S2 proceed
S1 stop, train ahead
3-state ABS:





S2 proceed (>1 block free)
S5 stop at next signal (1 block free)
S1 stop, train ahead
4-state ABS:








S2 proceed (>2 blocks free)
S3 reduce speed to 100 km/h (2 blocks free)
S5 stop at next signal (1 block free)
S1 stop, train ahead
other:


S1a is a special-case aspect, which forbids passing a signal displaying it, just like S1 on semi-automatic signals. It is used for safety reasons, for example, to forbid entering a tunnel during fire alarm. Other aspects are displayed normally, as in 3- or 4- state ABS.

(Unit - no aspect displayed) — on a track with bidirectional ABS, only the signals for currently set direction of travel will be illuminated; signals for "the opposite direction" will not be lit. A driver who finds himself approaching an unlit signal must stop the train and alert the dispatcher.

Distant-only signals

Distant-only signal (Pol. tarcza ostrzegawcza literally meaning warning shield) is used on lines not equipped with ABS. Placed in the braking distance, allows the driver to stop before the signal ahead. Its colour language is the same as signal aspects S2-S5, making them technically a signal which is just incapable of displaying a S1 (stop) aspect.

Their posts are painted grey and equipped with the distant-only signal sign.

Distant-only signals:


 Os1 there will be stop at the (next) signal

precedes S1, Sz



 Os2 there will be proceed with Vmax at the (next) signal

precedes a signal with no speed restriction on its near signal: S2, S3, S4, S5



 Os3 there will be speed reduction to 100 km/h at the signal

precedes a signal with a speed restriction of 100 km/h on its near signal: S6, S7, S8, S9



 Os4 there will be speed reduction to 40 or 60 km/h at the signal

precedes a signal with speed restriction of either 40 or 60 km/h on its near signal: S10a, S11a, S12a, S13a (60 km/h); S10, S11, S12, S13 (40 km/h)

Repeater signals

When a signal aspect is not visible from the proper distance (because of track curves for instance), a repeater signal is installed to aid drivers. Up to three repeaters may be installed if needed. A repeater signal is not a substitute for a distant-only signal.

Their posts are painted grey and equipped with plates with Roman numerals: III, II, I where the "I" stands closest to the main signal. Their colour language is identical to warning shields, except the fact they also have a continuously glowing white light, which informs that this is not a main signal but a repeater.

Repeater signal:



 Sp1 there will be S1 (stop) at the signal



 Sp2 there will be proceed with Vmax at the signal



 Sp3 there will be speed reduction to 100 km/h at the signal



 Sp4 there will be speed reduction to 40 or 60 km/h at the signal

The following table presents as an example, a station-entry signal designated "B" displaying the aspect S13 (speed limit 40 km/h, stop at the next signal) preceded with distant-only signal and three repeaters:

distant-only signal 3rd repeater 2nd repeater 1st repeater the main signal












ToB 3SpB 2SpB 1SpB B
braking distance
visibility distance

Level crossing warning

Level crossing warning is placed in a braking distance before an automatic level crossing. The signal tells the driver whether automobile drivers are warned about an approaching train (blinking red lights, barriers). Normally, level crossing warning signals display no aspect (i.e. are unlit). They light up in the front of an approaching train which is the first clue that the system is working correctly.

Level crossing warning signals are unrelated to other signals, therefore in case of Osp1 signal a train must proceed at 20 km/h regardless the higher speed allowed by last signal.

Their posts are painted black and white strips.

Level crossing warning signals
Osp1 Automatic level crossing is not working properly. The front of the train must pass the crossing with its speed limited to 20 km/h and be prepared for an immediate stop.
Osp2 Automatic level crossing operating properly. Proceed at normal speed.

Shunting signals

Shunting signal (Pol. tarcza manewrowa literally manoeuver shield) is used exclusively at stations. A consist shunting on such signals must not leave the station. Shunting signals are either stand-alone or incorporated into semi-automatic signals, which bear letter "m" on such occasions.

Stand-alone shunting signals have their posts painted gray.

Shunting signals:




Ms1 shunting forbidden
S1 stop and shunting forbidden




Ms2 shunting allowed

Old colour light signals

The colour light signals installed between 1959 and 1969 differ from the contemporary system. They are still in use on several stations. As a matter of fact they can also be used with ETCS Level 1, only the LEU unit must be reprogrammed to understand certain combinations of lights differently.

Semi-automatic signal configuration:
old new The old system did not use blinking lights, except the subsidiary signal, but that one was not popular at that times.

The pictures to the left present old and contemporary configuration with indication which colour chambers may blink if required.

There is a principle, observed then and now that two chambers of the same colour must be separated by a chamber of other colour.




Old and contemporary aspects of semi-automatic signal
old description contemporary






 S1 stop

the same expression

 S1











 S4 proceed at Vmax

the same expression

 S2





no equivalent for contemporary S3






 S6 reduce speed to 40 km/h

different expression

 S4











 S2 stop at next signal

the same expression

 S5





no equivalent for contemporary S6-S9, S10a-S13a, S11






 S5 proceed at 40km/h

different expression

 S10





 S12











 S3 proceed at 40 km/h, stop at next signal

the same expression

 S13





Old distant signals and repeaters
distant signal repeater With distant signals there is a principle that the chambers illuminating together, although of different colours, cannot be adjacent to each other. This explains why there are two chambers of orange colour next to each other.

With repeaters this principle is apparently not observed.


Old and contemporary aspects of distant signals and repeaters
old description contemporary


Ot1/Sp1 there will be stop at the signal

the same expression










Ot2/Sp2 there will be proceed at Vmax at the signal

the same expression










Ot3/Sp3 reduce speed to 40 km/h, there will be proceed at 40 km/h at the signal

different expression




Mechanical signals

Mechanical semaphore (day & night)

Sr1 stop
Sr2 clear
Sr3 clear slowly (40 km/h)
Mechanical distant signal

On/Od1/Ot1 expect stop
Od2/Ot2 expect clear
Ot3 expect clear slowly
Mechanical shunting signal

M1 shunting forbidden
M2 shunting allowed

External links

Polish railway signal simulators (Java applets)

This article is issued from Wikipedia - version of the 7/1/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.