Pockels effect

The Pockels effect (after Friedrich Carl Alwin Pockels who studied the effect in 1893), or Pockels electro-optic effect, changes or produces birefringence in an optical medium induced by an electric field. In the Pockels effect, also known as the linear electro-optic effect, the birefringence is proportional to the electric field. In the Kerr effect, the refractive index change (birefringence) is proportional to the square of the field. The Pockels effect occurs only in crystals that lack inversion symmetry, such as lithium niobate or gallium arsenide and in other noncentrosymmetric media such as electric-field poled polymers or glasses.

Pockels cells

Pockels cells are voltage-controlled wave plates. The Pockels effect is the basis of the operation of Pockels cells. Pockels cells may be used to rotate the polarization of a beam that passes through. See applications below for uses.

A transverse Pockels cell consists of two crystals in opposite orientation, which together give a zero-order wave plate when the voltage is turned off. This is often not perfect and drifts with temperature. But the mechanical alignment of the crystal axis is not so critical and is often done by hand without screws; while misalignment leads to some energy in the wrong ray (either e or o  for example, horizontal or vertical), in contrast to the longitudinal case, the loss is not amplified through the length of the crystal.

The electric field can be applied to the crystal medium either longitudinally or transversely to the light beam. Longitudinal Pockels cells need transparent or ring electrodes. Transverse voltage requirements can be reduced by lengthening the crystal.

Alignment of the crystal axis with the ray axis is critical. Misalignment leads to birefringence and to a large phase shift across the long crystal. This leads to polarization rotation if the alignment is not exactly parallel or perpendicular to the polarization.

Dynamics within the cell

Because of the high relative dielectric constant of εr ≈ 36 inside the crystal, changes in the electric field propagate at a speed of only c/6. Fast non-fiber optic cells are thus embedded into a matched transmission line. Putting it at the end of a transmission line leads to reflections and doubled switching time. The signal from the driver is split into parallel lines that lead to both ends of the crystal. When they meet in the crystal, their voltages add up. Pockels cells for fibre optics may employ a traveling wave design to reduce current requirements and increase speed.

Usable crystals also exhibit the piezoelectric effect to some degree[1] (RTP has the lowest, BBO and lithium niobate are high). After a voltage change, sound waves start propagating from the sides of the crystal to the middle. This is important not for pulse pickers, but for boxcar windows. Guard space between the light and the faces of the crystals needs to be larger for longer holding times. Behind the sound wave the crystal stays deformed in the equilibrium position for the high electric field. This increases the polarization. Due to the growing of the polarized volume the electric field in the crystal in front of the wave increases linearly, or the driver has to provide a constant current leakage.

The driver electronics

The driver must withstand the doubled voltage returned to it. Pockels cells behave like a capacitor. When switching these to high voltage, a high charge is needed; consequently, 3 ns switching requires about 40 A for a 5 mm aperture. Shorter cables reduce the amount of charge wasted in transporting current to the cell.

The driver may employ many transistors connected parallel and serial. The transistors are floating and need DC isolation for their gates. To do this, the gate signal is connected via optical fiber, or the gates are driven by a large transformer. In this case, careful compensation for feedback is needed to prevent oscillation.

The driver may employ a cascade of transistors and a triode. In a classic, commercial circuit the last transistor is an IRF830 MOSFET and the triode is an Eimac Y690 triode. The setup with a single triode has the lowest capacity; this even justifies turning off the cell by applying the double voltage. A resistor ensures the leakage current needed by the crystal and later to recharge the storage capacitor. The Y690 switches up to 10 kV and the cathode delivers 40 A if the grid is on +400 V. In this case the grid current is 8 A and the input impedance is thus 50 ohms, which matches standard coaxial cables, and the MOSFET can thus be placed remotely. Some of the 50 ohms are spent on an additional resistor which pulls the bias on −100 V. The IRF can switch 500 volts. It can deliver 18 A pulsed. Its leads function as an inductance, a storage capacitor is employed, the 50 ohm coax cable is connected, the MOSFET has an internal resistance, and in the end this is a critically damped RLC circuit, which is fired by a pulse to the gate of the MOSFET.

The gate needs 5 V pulses (range: ±20 V) while provided with 22 nC. Thus the current gain of this transistor is one for 3 ns switching, but it still has voltage gain. Thus it could theoretically also be used in common gate configuration and not in common source configuration. Transistors, which switch 40 V are typically faster, so in the previous stage a current gain is possible.

Applications of Pockels cells

Pockels Cells are used in a variety of scientific and technical applications:

See also


  1. Joseph Valasek, "Properties of Rochelle Salt Related to the Piezo-Electric Effect", Physics Review, 1922, Vol XIX, No. 478

External links

This article is issued from Wikipedia - version of the 9/27/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.