Solar panel

Solar PV modules (top) and two solar hot water panels (bottom) mounted on rooftops

Solar panel refers to a panel designed to absorb the sun's rays as a source of energy for generating electricity or heating.

A photovoltaic (PV) module is a packaged, connect assembly of typically 6×10 solar cells. Solar Photovoltaic panels constitute the solar array of a photovoltaic system that generates and supplies solar electricity in commercial and residential applications. Each module is rated by its DC output power under standard test conditions, and typically ranges from 100 to 365 watts. The efficiency of a module determines the area of a module given the same rated output  an 8% efficient 230 watt module will have twice the area of a 16% efficient 230 watt module. There are a few commercially available solar panels available that exceed 22% efficiency[1] and reportedly also exceeding 24%.[2][3] A single solar module can produce only a limited amount of power; most installations contain multiple modules. A photovoltaic system typically includes a panel or an array of solar modules, a solar inverter, and sometimes a battery and/or solar tracker and interconnection wiring.

The price of solar power has continued to fall so that in many countries it is cheaper than ordinary fossil fuel electricity from the grid (there is "grid parity").[4]

Theory and construction

See also: Solar cell
From a solar cell to a PV system

Solar modules use light energy (photons) from the sun to generate electricity through the photovoltaic effect. The majority of modules use wafer-based crystalline silicon cells or thin-film cells based on cadmium telluride or silicon. The structural (load carrying) member of a module can either be the top layer or the back layer. Cells must also be protected from mechanical damage and moisture. Most solar modules are rigid, but semi-flexible ones are available, based on thin-film cells.

Electrical connections are made in series to achieve a desired output voltage and/or in parallel to provide a desired current capability. The conducting wires that take the current off the modules may contain silver, copper or other non-magnetic conductive [transition metals]. The cells must be connected electrically to one another and to the rest of the system. Externally, popular terrestrial usage photovoltaic modules use MC3 (older) or MC4 connectors to facilitate easy weatherproof connections to the rest of the system.

Bypass diodes may be incorporated or used externally, in case of partial module shading, to maximize the output of module sections still illuminated.

Some recent solar module designs include concentrators in which light is focused by lenses or mirrors onto an array of smaller cells. This enables the use of cells with a high cost per unit area (such as gallium arsenide) in a cost-effective way.

There is also hotspot effect in solar modules in which two sides of cells are connected two diodes, this prevents solar modules or panels from short circuit.

Efficiencies

Reported timeline of solar cell energy conversion efficiencies since 1976 (National Renewable Energy Laboratory)

Depending on construction, photovoltaic modules can produce electricity from a range of frequencies of light, but usually cannot cover the entire solar range (specifically, ultraviolet, infrared and low or diffused light). Hence, much of the incident sunlight energy is wasted by solar modules, and they can give far higher efficiencies if illuminated with monochromatic light. Therefore, another design concept is to split the light into different wavelength ranges and direct the beams onto different cells tuned to those ranges. This has been projected to be capable of raising efficiency by 50%. Scientists from Spectrolab, a subsidiary of Boeing, have reported development of multi-junction solar cells with an efficiency of more than 40%, a new world record for solar photovoltaic cells.[5] The Spectrolab scientists also predict that concentrator solar cells could achieve efficiencies of more than 45% or even 50% in the future, with theoretical efficiencies being about 58% in cells with more than three junctions.

Currently the best achieved sunlight conversion rate (solar module efficiency) is around 21.5% in new commercial products[6] typically lower than the efficiencies of their cells in isolation. The most efficient mass-produced solar modules have power density values of up to 175 W/m2 (16.22 W/ft2).[7] Research by Imperial College, London has shown that the efficiency of a solar panel can be improved by studding the light-receiving semiconductor surface with aluminum nanocylinders similar to the ridges on Lego blocks. The scattered light then travels along a longer path in the semiconductor which means that more photons can be absorbed and converted into current. Although these nanocylinders have been used previously (aluminum was preceded by gold and silver), the light scattering occurred in the near infrared region and visible light was absorbed strongly. Aluminum was found to have absorbed the ultraviolet part of the spectrum, while the visible and near infrared parts of the spectrum were found to be scattered by the aluminum surface. This, the research argued, could bring down the cost significantly and improve the efficiency as aluminum is more abundant and less costly than gold and silver. The research also noted that the increase in current makes thinner film solar panels technically feasible without "compromising power conversion efficiencies, thus reducing material consumption".[8]

Micro-inverted solar panels are wired in parallel which produces more output than normal panels which are wired in series with the output of the series determined by the lowest performing panel (this is known as the "Christmas light effect"). Micro-inverters work independently so each panel contributes its maximum possible output given the available sunlight.[9]

Technology

Market-share of PV technologies since 1990

Most solar modules are currently produced from crystalline silicon (c-Si) solar cells made of multicrystalline and monocrystalline silicon. In 2013, crystalline silicon accounted for more than 90 percent of worldwide PV production, while the rest of the overall market is made up of thin-film technologies using cadmium telluride, CIGS and amorphous silicon[10] Emerging, third generation solar technologies use advanced thin-film cells. They produce a relatively high-efficiency conversion for the low cost compared to other solar technologies. Also, high-cost, high-efficiency, and close-packed rectangular multi-junction (MJ) cells are preferably used in solar panels on spacecraft, as they offer the highest ratio of generated power per kilogram lifted into space. MJ-cells are compound semiconductors and made of gallium arsenide (GaAs) and other semiconductor materials. Another emerging PV technology using MJ-cells is concentrator photovoltaics ( CPV ).

Thin film

In rigid thin-film modules, the cell and the module are manufactured in the same production line. The cell is created on a glass substrate or superstrate, and the electrical connections are created in situ, a so-called "monolithic integration". The substrate or superstrate is laminated with an encapsulant to a front or back sheet, usually another sheet of glass. The main cell technologies in this category are CdTe, or a-Si, or a-Si+uc-Si tandem, or CIGS (or variant). Amorphous silicon has a sunlight conversion rate of 6–12%

Flexible thin film cells and modules are created on the same production line by depositing the photoactive layer and other necessary layers on a flexible substrate. If the substrate is an insulator (e.g. polyester or polyimide film) then monolithic integration can be used. If it is a conductor then another technique for electrical connection must be used. The cells are assembled into modules by laminating them to a transparent colourless fluoropolymer on the front side (typically ETFE or FEP) and a polymer suitable for bonding to the final substrate on the other side.

Smart solar modules

Several companies have begun embedding electronics into PV modules. This enables performing maximum power point tracking (MPPT) for each module individually, and the measurement of performance data for monitoring and fault detection at module level. Some of these solutions make use of power optimizers, a DC-to-DC converter technology developed to maximize the power harvest from solar photovoltaic systems. As of about 2010, such electronics can also compensate for shading effects, wherein a shadow falling across a section of a module causes the electrical output of one or more strings of cells in the module to fall to zero, but not having the output of the entire module fall to zero.

Performance and degradation

Module performance is generally rated under standard test conditions (STC): irradiance of 1,000 W/m², solar spectrum of AM 1.5 and module temperature at 25 °C.

Electrical characteristics include nominal power (PMAX, measured in W), open circuit voltage (VOC), short circuit current (ISC, measured in amperes), maximum power voltage (VMPP), maximum power current (IMPP), peak power, (watt-peak, Wp), and module efficiency (%).

Nominal voltage refers to the voltage of the battery that the module is best suited to charge; this is a leftover term from the days when solar modules were only used to charge batteries. The actual voltage output of the module changes as lighting, temperature and load conditions change, so there is never one specific voltage at which the module operates. Nominal voltage allows users, at a glance, to make sure the module is compatible with a given system.

Open circuit voltage or VOC is the maximum voltage that the module can produce when not connected to an electrical circuit or system. VOC can be measured with a voltmeter directly on an illuminated module's terminals or on its disconnected cable.

The peak power rating, Wp, is the maximum output under standard test conditions (not the maximum possible output). Typical modules, which could measure approximately 1x2 meters or 2x4 feet, will be rated from as low as 75 watts to as high as 350 watts, depending on their efficiency. At the time of testing, the test modules are binned according to their test results, and a typical manufacturer might rate their modules in 5 watt increments, and either rate them at +/- 3%, +/-5%, +3/-0% or +5/-0%.[11][12][13][14]

Solar modules must withstand rain, hail, heavy snow load, and cycles of heat and cold for many years. Many crystalline silicon module manufacturers offer a warranty that guarantees electrical production for 10 years at 90% of rated power output and 25 years at 80%.[15]

Potential induced degradation (also called PID) is a potential induced performance degradation in crystalline photovoltaic modules, caused by so-called stray currents. This effect may cause power loss of up to 30 percent.

The largest challenge of photovoltaic technology is the efficiencies of such solar systems. While utilizing such systems draws a great interest due to the long term returns of profit, the efficacy needs to come a long way before making it plausible to be introduced in all consumers of electricity.

The problem resides in the enormous activation energy that must be overcome for a photon to excite an electron for harvesting purposes. Advancements in photovoltaic technologies have brought about the process of "doping" the silicon substrate to lower the activation energy thereby making the panel more efficient in converting photons to retrievable electrons.[16] Chemicals such as Boron (p-type) are applied into the semiconductor crystal in order to create donor and acceptor energy levels substantially closer to the valence and conductor bands.[17] In doing so, the addition of Boron impurity allows the activation energy to decrease 20 fold from 1.12 eV to 0.05 eV. Since the potential difference (EB) is so low, the Boron is able to thermally ionize at room temperatures. This allows for free energy carriers in the conduction and valence bands thereby allowing greater conversion of photons to electrons.

Solar power allows for greater efficiency than heat, such as the generation of energy in heat engines. The drawback with heat is that most of the heat created is lost to the surroundings. Thermal efficiency is as defined:

Due to the inherent irreversibility of heat production for useful work, efficiency levels are decreased. On the other hand, with solar panels there isn't a requirement to retain any heat, and there are no drawbacks such as friction.

Maintenance

Solar panel conversion efficiency, typically in the 20 percent range, is reduced by dust, grime, pollen, and other particulates that accumulate on the solar panel. "A dirty solar panel can reduce its power capabilities by up to 30 percent in high dust/pollen or desert areas", says Seamus Curran, associate professor of physics at the University of Houston and director of the Institute for NanoEnergy, which specializes in the design, engineering, and assembly of nanostructures.[18]

Paying to have solar panels cleaned is often not a good investment; researchers found panels that hadn’t been cleaned, or rained on, for 145 days during a summer drought in California, lost only 7.4 percent of their efficiency. Overall, for a typical residential solar system of 5 kilowatts, washing panels halfway through the summer would translate into a mere $20 gain in electricity production until the summer drought ends—in about 2 ½ months. For larger commercial rooftop systems, the financial losses are bigger but still rarely enough to warrant the cost of washing the panels. On average, panels lost a little less than 0.05 percent of their overall efficiency per day.[19]

Recycling

Most parts of a solar module can be recycled including up to 95% of certain semiconductor materials or the glass as well as large amounts of ferrous and non-ferrous metals.[20] Some private companies and non-profit organizations are currently engaged in take-back and recycling operations for end-of-life modules.[21]

Recycling possibilities depend on the kind of technology used in the modules:

Since 2010, there is an annual European conference bringing together manufacturers, recyclers and researchers to look at the future of PV module recycling.[27][28]

Production

# Top Module Producer Shipments in 2014 (MW)
1. Yingli 3,200
2. Trina Solar 2,580
3. Sharp Solar 2,100
4. Canadian Solar 1,894
5. Jinko Solar 1,765
6. ReneSola 1,728
7. First Solar 1,600
8. Hanwha SolarOne 1,280
9. Kyocera 1,200
10. JA Solar 1,173

In 2010, 15.9 GW of solar PV system installations were completed, with solar PV pricing survey and market research company PVinsights reporting growth of 117.8% in solar PV installation on a year-on-year basis.

With over 100% year-on-year growth in PV system installation, PV module makers dramatically increased their shipments of solar modules in 2010. They actively expanded their capacity and turned themselves into gigawatt GW players.[29] According to PVinsights, five of the top ten PV module companies in 2010 are GW players. Suntech, First Solar, Sharp, Yingli and Trina Solar are GW producers now, and most of them doubled their shipments in 2010.[30]

The basis of producing solar panels revolves around the use of silicon cells.[31] These silicon cells are typically 10-20% efficient[32] at converting sunlight into electricity, with newer production models now exceeding 22%.[33]

In order for solar panels to become more efficient, researchers across the world have been trying to develop new technologies to make solar panels more effective at turning sunlight into energy.[34]

In 2014, the world's top ten solar module producers in terms of shipped capacity during the calendar year of 2014 were Trina Solar, Yingli, Sharp Solar and Canadian Solar.[35]

Price

See also: Grid parity
Swanson's law states that with every doubling of production of panels, there has been a 20 percent reduction in the cost of panels.[36]

Average pricing information divides in three pricing categories: those buying small quantities (modules of all sizes in the kilowatt range annually), mid-range buyers (typically up to 10 MWp annually), and large quantity buyers (self-explanatory—and with access to the lowest prices). Over the long term there is clearly a systematic reduction in the price of cells and modules. For example, in 2012 it was estimated that the quantity cost per watt was about US$0.60, which was 250 times lower than the cost in 1970 of US$150.[37][38] A 2015 study shows price/kWh dropping by 10% per year since 1980, and predicts that solar could contribute 20% of total electricity consumption by 2030, whereas the International Energy Agency predicts 16% by 2050.[39]

Real world energy production costs depend a great deal on local weather conditions. In a cloudy country such as the United Kingdom, the cost per produced kWh is higher than in sunnier countries like Spain.

Following to RMI, Balance-of-System (BoS) elements, this is, non-module cost of non-microinverter solar modules (as wiring, converters, racking systems and various components) make up about half of the total costs of installations.

For merchant solar power stations, where the electricity is being sold into the electricity transmission network, the cost of solar energy will need to match the wholesale electricity price. This point is sometimes called 'wholesale grid parity' or 'busbar parity'.[4]

Some photovoltaic systems, such as rooftop installations, can supply power directly to an electricity user. In these cases, the installation can be competitive when the output cost matches the price at which the user pays for his electricity consumption. This situation is sometimes called 'retail grid parity', 'socket parity' or 'dynamic grid parity'.[40] Research carried out by UN-Energy in 2012 suggests areas of sunny countries with high electricity prices, such as Italy, Spain and Australia, and areas using diesel generators, have reached retail grid parity.[4]

Mounting and tracking

Solar modules mounted on solar trackers
Double glass photovoltaic solar modules, installed in a support structure.

Ground mounted photovoltaic system are usually large, utility-scale solar power plants. Their solar modules are held in place by racks or frames that are attached to ground based mounting supports.[41][42] Ground based mounting supports include:

Roof-mounted solar power systems consist of solar modules held in place by racks or frames attached to roof-based mounting supports.[43] Roof-based mounting supports include:

Solar trackers increase the amount of energy produced per module at a cost of mechanical complexity and need for maintenance. They sense the direction of the Sun and tilt or rotate the modules as needed for maximum exposure to the light.[44][45] Alternatively, fixed racks hold modules stationary as the sun moves across the sky. The fixed rack sets the angle at which the module is held. Tilt angles equivalent to an installation's latitude are common. Most of these fixed racks are set on poles above ground.[46] Panels that face West or East may provide slightly lower energy, but evens out the supply, and may provide more power during peak demand.[47]

Standards

Standards generally used in photovoltaic modules:

Applications

There are many practical applications for the use of solar panels or photovoltaics. It can first be used in agriculture as a power source for irrigation. In health care solar panels can be used to refrigerate medical supplies. It can also be used for infrastructure. PV modules are used in photovoltaic systems and include a large variety of electric devices:

Gallery

See also

References

  1. Ulanoff, L. Elon Musk and SolarCity unveil ‘world’smost efficient’ solar panel, Mashable, October 2, 2015, accessed June 28, 2016
  2. Milestone in solar cell efficiency achieved: New record for unfocused sunlight edges closer to theoretic limits. Wilson da Silva. Science Daily. May 17, 2016
  3. [University of New South Wales. "Milestone in solar cell efficiency achieved: New record for unfocused sunlight edges closer to theoretic limits." ScienceDaily. ScienceDaily, 17 May 2016. <www.sciencedaily.com/releases/2016/05/160517121811.htm>]
  4. 1 2 3 Morgan Baziliana; et al. (17 May 2012). Re-considering the economics of photovoltaic power. UN-Energy (Report). United Nations. Retrieved 20 November 2012.
  5. KING, R.R., et al., Appl. Phys. Letters 90 (2007) 183516.
  6. "SunPower e20 Module".
  7. "HIT® Photovoltaic Module" (PDF). Sanyo / Panasonic. Retrieved 25 November 2016.
  8. "Improving the efficiency of solar panels". The Hindu. 24 October 2013. Retrieved 24 October 2013.
  9. "Micro Inverters for Residential Solar Arrays". Retrieved 2015-09-29.
  10. Photovoltaics Report, Fraunhofer ISE, 28 July 2014, pages 18,19
  11. "First Solar – FS-377 / FS-380 / FS-382 / FS-385 Datasheet" (PDF). Retrieved 2012-06-04.
  12. "TSM PC/PM14 Datasheet" (PDF). Retrieved 2012-06-04.
  13. "YGE 235 Data sheet" (PDF). Retrieved 2012-06-04.
  14. "CTI Solar sales brochure" (PDF). cti-solar.com. Retrieved 3 September 2010.
  15. "How Solar Cells Work". HowStuffWorks. Retrieved 2015-12-09.
  16. "Bonding in Metals and Semiconductors". 2012books.lardbucket.org. Retrieved 2015-12-09.
  17. Crawford, Mike (October 2012). "Self-Cleaning Solar Panels Maximize Efficiency". The American Society of Mechanical Engineers. ASME. Retrieved 15 September 2014.
  18. Patringenaru, Ioana (August 2013). "Cleaning Solar Panels Often Not Worth the Cost, Engineers at UC San Diego Find". UC San Diego News Center. UC San Diego News Center. Retrieved 31 May 2015.
  19. Lisa Krueger. 1999. "Overview of First Solar's Module Collection and Recycling Program" (PDF). Brookhaven National Laboratory p. 23. Retrieved August 2012. Check date values in: |access-date= (help)
  20. Karsten Wambach. 1999. "A Voluntary Take Back Scheme and Industrial Recycling of Photovoltaic Modules" (PDF). Brookhaven National Laboratory p. 37. Retrieved August 2012. Check date values in: |access-date= (help)
  21. Krueger. 1999. p. 12-14
  22. Wambach. 1999. p. 15
  23. Wambach. 1999. p. 17
  24. Krueger. 1999. p. 23
  25. Wambach. 1999. p. 23
  26. "First Breakthrough In Solar Photovoltaic Module Recycling, Experts Say". European Photovoltaic Industry Association. Retrieved January 2011. Check date values in: |access-date= (help)
  27. "3rd International Conference on PV Module Recycling". PV CYCLE. Retrieved October 2012. Check date values in: |access-date= (help)
  28. "Solar Power Plant Report".
  29. "PVinsights announces worldwide 2010 top 10 ranking of PV module makers". www.pvinsights.com. Retrieved 2011-05-06.
  30. http://www.solarpowerworldonline.com/2013/05/what-are-solar-panels-made-of/
  31. http://www.engineeringchallenges.org/cms/8996/9082.aspx
  32. "SolarCity Press Release".
  33. https://www.asme.org/engineering-topics/articles/renewable-energy/making-solar-panels-more-efficient
  34. "Leaders and laggards of the top 10 PV module manufacturers in 2014". PV Tech. Retrieved 2015-02-21.
  35. "Swanson's Law and Making US Solar Scale Like Germany". Greentech Media. 24 November 2014.
  36. ENF Ltd. (8 January 2013). "Small Chinese Solar Manufacturers Decimated in 2012 | Solar PV Business News | ENF Company Directory". Enfsolar.com. Retrieved 29 August 2013.
  37. Harnessing Light. National Research Council. 1997. p. 162.
  38. J. Doyne Farmer, François Lafond (2 November 2015). "How predictable is technological progress?". doi:10.1016/j.respol.2015.11.001. License: cc. Note: Appendix F. A trend extrapolation of solar energy capacity.
  39. "Solar Photovoltaics competing in the energy sector – On the road to competitiveness" (PDF). EPIA. Retrieved August 2012. Check date values in: |access-date= (help)
  40. SolarProfessional.com Ground-Mount PV Racking Systems March 2013
  41. Massachusetts Department of Energy Resources Ground-Mounted Solar Photovoltaic Systems, December 2012
  42. "A Guide To Photovoltaic System Design And Installation". ecodiy.org. Retrieved 2011-07-26.
  43. Shingleton, J. "One-Axis Trackers – Improved Reliability, Durability, Performance, and Cost Reduction" (PDF). National Renewable Energy Laboratory. Retrieved 30 December 2012.
  44. Mousazadeh, Hossain; et al. "A review of principle and sun-tracking methods for maximizing" (PDF). Renewable and Sustainable Energy Reviews 13 (2009) 1800–1818. Elsevier. Retrieved 30 December 2012.
  45. "Optimum Tilt of Solar Panels". MACS Lab. Retrieved 19 October 2014.
  46. http://www.telegraph.co.uk/news/earth/energy/solarpower/10996273/Most-solar-panels-are-facing-the-wrong-direction-say-scientists.html
Wikimedia Commons has media related to Photovoltaics.
This article is issued from Wikipedia - version of the 12/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.