Phosphorus pentoxide

Phosphorus pentoxide
Names
Other names
Diphosphorus pentoxide
Phosphorus(V) oxide
Phosphoric anhydride
Tetraphosphorus decaoxide
Tetraphosphorus decoxide
Identifiers
1314-56-3 YesY
16752-60-6 (P4O10) N
3D model (Jmol) Interactive image
ChEBI CHEBI:37376 YesY
ChemSpider 14128 YesY
ECHA InfoCard 100.013.852
PubChem 14812
RTECS number TH3945000
Properties
P4O10
Molar mass 283.886 g mol−1
Appearance white powder
very deliquescent
pungent odour
Density 2.39 g/cm3
Melting point sublimes
Boiling point 360 °C (680 °F; 633 K)
exothermic hydrolysis
Vapor pressure 1 mmHg @ 385 °C (stable form)
Hazards
Safety data sheet MSDS
not listed
NFPA 704
Flammability code 1: Must be pre-heated before ignition can occur. Flash point over 93 °C (200 °F). E.g., canola oil Health code 3: Short exposure could cause serious temporary or residual injury. E.g., chlorine gas Reactivity code 3: Capable of detonation or explosive decomposition but requires a strong initiating source, must be heated under confinement before initiation, reacts explosively with water, or will detonate if severely shocked. E.g., fluorine Special hazards (white): no codeNFPA 704 four-colored diamond
1
3
3
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
N verify (what is YesYN ?)
Infobox references

Phosphorus pentoxide is a chemical compound with molecular formula P4O10 (with its common name derived from its empirical formula, P2O5). This white crystalline solid is the anhydride of phosphoric acid. It is a powerful desiccant and dehydrating agent.

Structure

Phosphorus pentoxide crystallizes in at least four forms or polymorphs. The most familiar one, a metastable form,[1] shown in the figure, comprises molecules of P4O10. Weak van der Waals forces hold these molecules together in a hexagonal lattice (However, in spite of the high symmetry of the molecules, the crystal packing is not a close packing[2]). The structure of the P4O10 cage is reminiscent of adamantane with Td symmetry point group.[3] It is closely related to the corresponding anhydride of phosphorous acid, P4O6. The latter lacks terminal oxo groups. Its density is 2.30 g/cm3. It boils at 423 °C under atmospheric pressure; if heated more rapidly it can sublimate. This form can be made by condensing the vapor of phosphorus pentoxide rapidly, the result is an extremely hygroscopic solid.[4]

The other polymorphs are polymeric, but in each case the phosphorus atoms are bound by a tetrahedron of oxygen atoms, one of which forms a terminal P=O bond involving the donation of the terminal oxygen p-orbital electrons to the antibonding phosphorus-oxygen single bonds. The macromolecular form can be made by heating the compound in a sealed tube for several hours, and maintaining the melt at a high temperature before cooling the melt to the solid.[4] The metastable orthorhombic, "O"-form (density 2.72 g/cm3, melting point 562 °C), adopts a layered structure consisting of interconnected P6O6 rings, not unlike the structure adopted by certain polysilicates. The stable form is a higher density phase, also orthorhombic, the so-called O' form. It consists of a 3-dimensional framework, density 3.5 g/cm3.[1][5] The remaining polymorph is a glass or amorphous form; it can be made by fusing any of the others.

part of an o′-(P2O5) layer
o′-(P2O5) layers stacking

Preparation

P4O10 is prepared by burning elemental phosphorus with sufficient supply of air:

P4 + 5 O2 → P4O10

For most of the 20th century, phosphorus pentoxide was used to provide a supply of concentrated pure phosphoric acid. In the thermal process, the phosphorus pentoxide obtained by burning white phosphorus was dissolved in dilute phosphoric acid to produce concentrated acid.[6] Improvements in filter technology is leading to the "wet phosphoric acid process" taking over from the thermal process, obviating the need to produce white phosphorus as a starting material.[7] The dehydration of phosphoric acid to give phosphorus pentoxide is not possible as on heating metaphosphoric acid will boil without losing all its water.

Applications

Phosphorus pentoxide is a potent dehydrating agent as indicated by the exothermic nature of its hydrolysis:

P4O10 + 6 H2O → 4 H3PO4   (–177 kJ)

However, its utility for drying is limited somewhat by its tendency to form a protective viscous coating that inhibits further dehydration by unspent material. A granular form of P4O10 is used in desiccators.

Consistent with its strong desiccating power, P4O10 is used in organic synthesis for dehydration. The most important application is for the conversion of primary amides into nitriles:[8]

P4O10 + RC(O)NH2 → P4O9(OH)2 + RCN

The indicated coproduct P4O9(OH)2 is an idealized formula for undefined products resulting from the hydration of P4O10.

Alternatively, when combined with a carboxylic acid, the result is the corresponding anhydride:[9]

P4O10 + RCO2H → P4O9(OH)2 + [RC(O)]2O

The "Onodera reagent", a solution of P4O10 in DMSO, is employed for the oxidation of alcohols.[10] This reaction is reminiscent of the Swern oxidation.

The desiccating power of P4O10 is strong enough to convert many mineral acids to their anhydrides. Examples: HNO3 is converted to N2O5;  H2SO4 is converted to SO3;  HClO4 is converted to Cl2O7;  HCF3SO3 is converted to (CF3)2S2O5.

Between the commercially important P4O6 and P4O10, phosphorus oxides are known with intermediate structures.[11]

Hazards

Phosphorus pentoxide is not flammable. It reacts vigorously with water and water-containing substances like wood or cotton, liberates much heat and may even cause fire. It is corrosive to metal and is very irritating – it may cause severe burns to the eye, skin, mucous membrane, and respiratory tract even at concentrations as low as 1 mg/m3.[12]

Fiction

See also

References

  1. 1 2 Greenwood, Norman N.; Earnshaw, Alan (1997). Chemistry of the Elements (2nd ed.). Butterworth-Heinemann. ISBN 0-08-037941-9.
  2. Cruickshank, D.W.J. (1964). "Refinements of Structures Containing Bonds between Si, P, S or Cl and O or N: V. P4O10". Acta Crystallogr. 17 (6): 677–9. doi:10.1107/S0365110X64001669.
  3. D. E. C. Corbridge "Phosphorus: An Outline of its Chemistry, Biochemistry, and Technology" 5th Edition Elsevier: Amsterdam. ISBN 0-444-89307-5.
  4. 1 2 .Catherine E. Housecroft; Alan G. Sharpe (2008). "Chapter 15: The group 15 elements". Inorganic Chemistry, 3rd Edition. Pearson. p. 473. ISBN 978-0-13-175553-6.
  5. D. Stachel, I. Svoboda and H. Fuess (June 1995). "Phosphorus Pentoxide at 233 K". Acta Crystallogr. C. 51 (6): 1049–1050. doi:10.1107/S0108270194012126.
  6. Threlfall, Richard E., (1951). The story of 100 years of Phosphorus Making: 1851 - 1951. Oldbury: Albright & Wilson Ltd
  7. Podger, Hugh (2002). Albright & Wilson: The Last 50 Years. Studley: Brewin Books. ISBN 1-85858-223-7
  8. Meier, M. S. "Phosphorus(V) Oxide" in Encyclopedia of Reagents for Organic Synthesis (Ed: L. Paquette) 2004, J. Wiley & Sons, New York. doi:10.1002/047084289.
  9. Joseph C. Salamone, ed. (1996). Polymeric materials encyclopedia: C, Volume 2. CRC Press. p. 1417. ISBN 0-8493-2470-X.
  10. Tidwell, T. T. "Dimethyl Sulfoxide–Phosphorus Pentoxide" in Encyclopedia of Reagents for Organic Synthesis (Ed: L. Paquette) 2004, J. Wiley & Sons, New York. doi:10.1002/047084289.
  11. Luer, B.; Jansen, M. "Crystal Structure Refinement of Tetraphosphorus Nonaoxide, P4O9" Zeitschrift fur Kristallographie 1991, volume 197, pages 247-8.
  12. Phosphorus pentoxide MSDS
This article is issued from Wikipedia - version of the 12/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.