Four-bar linkage

A planar four-bar linkage (Watt linkage) used as a train suspension.
A Bennett spatial four-bar linkage.

A four-bar linkage, also called a four-bar, is the simplest movable closed chain linkage. It consists of four bodies, called bars or links, connected in a loop by four joints. Generally, the joints are configured so the links move in parallel planes, and the assembly is called a planar four-bar linkage.[1]

If the linkage has four hinged joints with axes angled to intersect in a single point, then the links move on concentric spheres and the assembly is called a spherical four-bar linkage. Bennett's linkage is a spatial four-bar linkage with hinged joints that have their axes angled in a particular way that makes the system movable.[2][3]

Planar four-bar linkage

Animated four-bar linkage

Planar four-bar linkages are constructed from four links connected in a loop by four one degree of freedom joints. A joint may be either a revolute, that is a hinged joint, denoted by R, or a prismatic, as sliding joint, denoted by P.

A link connected to ground by a hinged joint is usually called a crank. A link connected to ground by a prismatic joint is called a slider. Sliders are sometimes considered to be cranks that have a hinged pivot at an extremely long distance away perpendicular to the travel of the slider.

The link that connects two cranks is called a floating link or coupler. A coupler that connects a crank and a slider, it is often called a connecting rod.

There are three basic types of planar four-bar linkage depending on the use of revolute or prismatic joints:

  1. Four revolute joints: The planar quadrilateral linkage is formed by four links and four revolute joints, denoted RRRR. It consists of two cranks connected by a coupler.
  2. Three revolute joints and a prismatic joint: The slider-crank linkage is constructed from four links connected by three revolute and one prismatic joint, or RRRP. It can be constructed with crank and a slider connected by the connecting rod. Or it can be constructed as a two cranks with the slider acting as the coupler, known as an inverted slider-crank.
  3. Two revolute joints and two prismatic joints: The double slider is a PRRP linkage.[3] This linkage is constructed by connecting two sliders with a coupler link. If the directions of movement of the two sliders are perpendicular then the trajectories of the points in the coupler are ellipses and the linkage is known as an elliptical trammel, or the Trammel of Archimedes.

Planar four-bar linkages are important mechanisms found in machines. The kinematics and dynamics of planar four-bar linkages are important topics in mechanical engineering.

Planar four-bar linkages can be designed to guide a wide variety of movements.

Planar quadrilateral linkage

Planar quadrilateral linkage, RRRR or 4R linkages have four rotating joints. One link of the chain is usually fixed, and is called the ground link, fixed link, or the frame. The two links connected to the frame are called the grounded links and are generally the input and output links of the system, sometimes called the input link and output link. The last link is the floating link, which is also called a coupler or connecting rod because it connects an input to the output.

Assuming the frame is horizontal there are four possibilities for the input and output links:[3]

Some authors do not distinguish between the types of rocker.

Grashof condition

The Grashof condition for a four-bar linkage states: If the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. In other words, the condition is satisfied if S+LP+Q where S is the shortest link, L is the longest, and P and Q are the other links.

Classification

The movement of a quadrilateral linkage can be classified into eight cases based on the dimensions of its four links. Let a, b, g and h denote the lengths of the input crank, the output crank, the ground link and floating link, respectively. Then, we can construct the three terms:

The movement of a quadrilateral linkage can be classified into eight types based on the positive and negative values for these three terms, T1, T2, and T3.[3]

Grashof condition Input link Output link
+ Grashof Crank Crank
+ + + Grashof Crank Rocker
+ Grashof Rocker Crank
+ Grashof Rocker Rocker
Non-Grashof 0-Rocker 0-Rocker
+ + Non-Grashof π-Rocker π-Rocker
+ + Non-Grashof π-Rocker 0-Rocker
+ + Non-Grashof 0-Rocker π-Rocker

The cases of T1= 0, T2=0, and T3=0 are interesting because the linkages fold. If we distinguish folding quadrilateral linkage, then there are 27 different cases.

The figure shows examples of the various cases for a planar quadrilateral linkage.[4]

Types of four-bar linkages, s = shortest link, l = longest link.

The configuration of a quadrilateral linkage may be classified into three types: convex, concave, and crossing. In the convex and concave cases no two links cross over each other. In the crossing linkage two links cross over each other. In the convex case all four internal angles are less than 180 degrees, and in the concave configuration one internal angle is greater than 180 degrees. There exists a simple geometrical relationship between the lengths of the two diagonals of the quadrilateral. For convex and crossing linkages, the length of one diagonal increases if and only if the other decreases. On the other hand, for nonconvex non-crossing linkages, the opposite is the case; one diagonal increases if and only if the other also increases.[5]

Design of four bar mechanisms

The synthesis, or design, of four bar mechanisms is important when aiming to produce a desired output motion for a specific input motion. In order to minimize cost and maximize efficiency, a designer will choose the simplest mechanism possible to accomplish the desired motion. When selecting a mechanism type to be designed, link lengths must be determined by a process called dimensional synthesis. Dimensional synthesis involves an iterate-and-analyze methodology which in certain circumstances can be an inefficient process; however, in unique scenarios, exact and detailed procedures to design an accurate mechanism may not exist.[6]

Time ratio

The time ratio (Q) of a four bar mechanism is a measure of its quick return and is defined as follows:[6]

With four bar mechanisms there are two strokes, the forward and return, which when added together create a cycle. Each stroke may be identical or have different average speeds. The time ratio numerically defines how fast the forward stroke is compared to the quicker return stroke. The total cycle time (Δtcycle) for a mechanism is:[6]

Most four bar mechanisms are driven by a rotational actuator, or crank, that requires a specific constant speed. This required speed (ωcrank)is related to the cycle time as follows:[6]

Some mechanisms that produce reciprocating, or repeating, motion are designed to produce symmetrical motion. That is, the forward stroke of the machine moves at the same pace as the return stroke. These mechanisms, which are often referred to as in-line design, usually do work in both directions, as they exert the same force in both directions.[6]

Examples of symmetrical motion mechanisms include:

Other applications require that the mechanism-to-be-designed has a faster average speed in one direction than the other. This category of mechanism is most desired for design when work is only required to operate in one direction. The speed at which this one stroke operates is also very important in certain machine applications. In general, the return and work-non-intensive stroke should be accomplished as fast as possible. This is so the majority of time in each cycle is allotted for the work-intensive stroke. These quick-return mechanisms are often referred to as offset.[6]

Examples of offset mechanisms include:

With offset mechanisms, it is very important to understand how and to what degree the offset affects the time ratio. To relate the geometry of a specific linkage to the timing of the stroke, an imbalance angle (β) is used. This angle is related to the time ratio, Q, as follows:[6]

Through simple algebraic rearrangement, this equation can be rewritten to solve for β:[6]

Timing charts

Timing charts are often used to synchronize the motion between two or more mechanisms. They graphically display information showing where and when each mechanism is stationary or performing its forward and return strokes. Timing charts allow designers to qualitatively describe the required kinematic behavior of a mechanism.[6]

These charts are also used to estimate the velocities and accelerations of certain four bar links. The velocity of a link is the time rate at which its position is changing, while the link's acceleration is the time rate at which its velocity is changing. Both velocity and acceleration are vector quantities, in that they have both magnitude and direction; however, only their magnitudes are used in timing charts. When used with two mechanisms, timing charts assume constant acceleration. This assumption produces polynomial equations for velocity as a function of time. Constant acceleration allows for the velocity vs. time graph to appear as straight lines, thus designating a relationship between displacement (ΔR), maximum velocity (vpeak), acceleration (a), and time(Δt). The following equations show this.[6][7]

ΔR = vpeakΔt
ΔR = a(Δt)^2

Given the displacement and time, both the maximum velocity and acceleration of each mechanism in a given pair can be calculated.[6]

Slider-crank linkage

A slider-crank linkage is a four-bar linkage with three revolute joints and one prismatic, or sliding, joint. The rotation of the crank drives the linear movement the slider, or the expansion of gases against a sliding piston in a cylinder can drive the rotation of the crank.

There are two types of slider-cranks: in-line and offset.

  1. In-line: An in-line slider-crank has its slider positioned so the line of travel of the hinged joint of the slider passes through the base joint of the crank. This creates a symmetric slider movement back and forth as the crank rotates.
  2. Offset: If the line of travel of the hinged joint of the slider does not pass though the base pivot of the crank, the slider movement is not symmetric. It moves faster in one direction than the other. This is called a quick-return mechanism.

There are also two methods to design each type: graphical and analytical.[6]

Design

In-line slider crank animation (click to animate)

An in-line crank slider is oriented in a way in which the pivot point of the crank is coincident with the axis of the linear movement. The follower arm, which is the link that connects the crank arm to the slider, connects to a pin in the center of sliding object. This pin is considered to be on the linear movement axis. Therefore, to be considered an in-line crank slider, the pivot point of the crank arm must be in-line with this pin point. The stroke((ΔR4)max) of an in-line crank slider is defined as the maximum linear distance the slider may travel between the two extreme points of its motion. With an in-line crank slider, the motion of the crank and follower links is symmetric about the sliding axis. This means that the crank angle required to execute a forward stroke is equivalent to the angle required to perform a reverse stroke. For this reason, the in-line slider-crank mechanism produces balanced motion. This balanced motion implies other ideas as well. Assuming the crank arm is driven at a constant velocity, the time it takes to perform a forward stroke is equal to the time it takes to perform a reverse stroke.[6]

Graphical approach

The graphical method of designing an in-line slider-crank mechanism involves the usage of hand-drawn or computerized diagrams. These diagrams are drawn to scale in order for easy evaluation and successful design. Basic trigonometry, the practice of analyzing the relationship between triangle features in order to determine any unknown values, can be used with a graphical compass and protractor alongside these diagrams to determine the required stroke or link lengths.[6]

When the stroke of a mechanism needs to be calculated, first identify the ground level for the specified slider-crank mechanism. This ground level is the axis on which both the crank arm pivot-point and the slider pin are positioned. Draw the crank arm pivot point anywhere on this ground level. Once the pin positions are correctly placed, set a graphical compass to the given link length of the crank arm. Positioning the compass point on the pivot point of the crank arm, rotate the compass to produce a circle with radius equal to the length of the crank arm. This newly drawn circle represents the potential motion of the crank arm. Next, draw two models of the mechanism. These models will be oriented in a way that displays both the extreme positions of the slider. Once both diagrams are drawn, the linear distance between the retracted slider and the extended slider can be easily measured to determine the slider-crank stroke.[6]

The retracted position of the slider is determined by further graphical evaluation. Now that the crank path is found, draw the crank slider arm in the position that places it as far away as possible from the slider. Once drawn, the crank arm should be coincident with the ground level axis that was initially drawn. Next, from the free point on the crank arm, draw the follower link using its measured or given length. Draw this length coincident with the ground level axis but in the direction toward the slider. The unhinged end of the follower will now be at the fully retracted position of the slider. Next, the extended position of the slider needs to be determined. From the pivot point of the crank arm, draw a new crank arm coincident with the ground level axis but in a position closest to the slider. This position should put the new crank arm at an angle of 180 degrees away from the retracted crank arm. Then draw the follower link with its given length in the same manner as previously mentioned. The unhinged point of the new follower will now be at the fully extended position of the slider.[6]

Both the retracted and extended positions of the slider should now be known. Using a measuring ruler, measure the distance between these two points. This distance will be the mechanism stroke, ((ΔR4)max).[6]

Analytical approach

To analytically design an in-line crank slider and achieve the desired stroke, the appropriate lengths of the two links, the crank and follower, need to be determined . For this case, the crank arm will be referred to as L2, and the follower link will be referred to as L3. With all in-line slider-crank mechanisms, the stroke is twice the length of the crank arm. Therefore, given the stroke, the length of the crank arm can be determined. This relationship is represented as:[6]

L2 = (ΔR4)max ÷ 2

Once L2 is found, the follower length (L3) can be determined. However, because the stroke of the mechanism only depends on the crank arm length, the follower length is somewhat insignificant. As a general rule, the length of the follower link should be at least 3 times the length of the crank arm. This is to account for an often undesired increased acceleration yield, or output, of the connecting arm.[6]

Offset slider-crank design

With an offset slider-crank mechanism, an offset distance is introduced. This offset distance is referred to as L1 and is the fixed distance between the crank arm pivot point and the slider axis. This offset distance means that the slider-crank motion is no longer symmetrical about the sliding axis. In addition, the required crank angles of the forward and reverse strokes are no longer equivalent. An offset slider-crank provides a quick return when a slower working stroke is desired.[6]

With offset slider-cranks, the stroke is always twice the crank length, and as the offset distance increases, the stroke also becomes larger. The potential range for the offset distance can be written in relation to the other mechanism lengths, L2and L3, as the equation:[6]

L1 < L3 - L2

The design of an in-line crank slider mechanism involves finding the two link lengths, L2 and L3, and an appropriate offset distance, L1, in order to achieve the wanted stroke, (ΔR4)max, and imbalance angle, β.

Analytical approach

The analytical method for designing an offset crank slider mechanism is the process by which triangular geometry is evaluated in order to determine generalized relationships among certain lengths, distances, and angles. These generalized relationships are displayed in the form of 3 equations and can be used to determine unknown values for almost any offset slider-crank. These equations express the link lengths, L1, L2, and L3, as a function of the stroke,(ΔR4)max, the imbalance angle, β, and the angle of an arbitrary line M, θM. Arbitrary line M is a designer-unique line that runs through the crank pivot point and the extreme retracted slider position. The 3 equations are as follows:[6]

L1 = (ΔR4)max × [(sin(θM)sin(θM - β)) / sin(β)]
L2 = (ΔR4)max × [(sin(θM) - sin(θM - β)) / 2sin(β)]
L3 = (ΔR4)max × [(sin(θM) + sin(θM - β)) / 2sin(β)]

With these relationships, the 3 link lengths can be calculated and any related unknown values can be determined.

Examples

A four-bar linkage used as the suspension for a bicycle. If we count the two bars that form the shock absorber attached to the output link, then this is a Watt II six-bar linkage

See also

References

  1. Hartenberg, R.S. & J. Denavit (1964) Kinematic synthesis of linkages, New York: McGraw-Hill, online link from Cornell University.
  2. Hunt, K. H., Kinematic Geometry of Mechanisms, Oxford Engineering Science Series, 1979
  3. 1 2 3 4 J. M. McCarthy and G. S. Soh, Geometric Design of Linkages, 2nd Edition, Springer 2010
  4. Design of Machinery 3/e, Robert L. Norton, 2 May 2003, McGraw Hill. ISBN 0-07-247046-1
  5. Toussaint, G. T., "Simple proofs of a geometric property of four-bar linkages," American Mathematical Monthly, June/July 2003, pp. 482–494.
  6. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Myszka, David (2012). Machines and Mechanisms: Applied Kinematic Analysis. New Jersey: Pearson Education. ISBN 978-0-13-215780-3.
  7. Chakrabarti, Amaresh (2002). Engineering Design Synthesis: Understanding, Approaches and Tools. Great Britain: Springer-Verlag London Limited. ISBN 1852334924.
Wikimedia Commons has media related to Four-bar linkage.
This article is issued from Wikipedia - version of the 11/6/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.