Colt Police Positive
|Colt Police Positive|
Blued Colt Police Positive revolver; six inch barrel
|Place of origin||United States|
|Manufacturer||Colt's Manufacturing Company|
|Feed system||six round cylinder|
|Sights||Fixed iron; half-moon blade front, V-notch rear|
The Colt Police Positive is a small-frame, double-action revolver featuring a six-round cylinder, chambered for either .32 or .38 caliber cartridges. Designed primarily for sale to federal, state, or local law enforcement agencies, the Police Positive was introduced into the firearms market by Colt's Manufacturing Company in 1907.
Development and history
The Colt Police Positive was an improvement of Colt’s earlier “New Police” revolver, upgraded with an internal hammer block safety. Colt named this new security device the “Positive Lock”, and its nomenclature ended up being incorporated as a partial namesake for the new revolver. The cylinder of the Police Positive rotated in the clockwise direction, the opposite of firearms maker Smith & Wesson's competing models. Ever a canny competitor in the firearms milieu, Colt missed no opportunity to score a coup d'éclat over its arch rival, and began a marketing campaign which accentuated this detail. In its advertising Colt proclaimed that "All Colt cylinders TURN TO THE RIGHT", and suggested that the Colt design forced the cylinder crane up against the frame, resulting in tighter lockup with less play and better chamber to barrel alignment, thus markedly increasing accuracy. The Police Positive was very successful; along with the Colt Official Police it dominated the law enforcement firearms market in the early 1900s. The Positive was itself incrementally modified in 1908, forming the basis for Colt’s Police Positive Special model.
A nickel Police Positive with pearl grips & .32 calibre was used by Charles Bronson as Paul Kersey in Death Wish. The notorious American gangster Al Capone also used a Police Positive, a nickel .38 Police Positive with walnut grips and a 4-inch barrel, manufactured in 1929. In June 2011 a private collector sold it at Christie's for the sum of £67,250/$109,080/€75,656.
The Police Positive was made of carbon steel, and was finished with either a polished blued finish or nickel-plated. The First issue of the Police Positive ran from the revolver’s introduction in 1907 until 1927. Sporting Colt’s standard hard rubber grips, it was offered with barrel lengths of 2.5 (available only in .32 caliber), 4, 5, and 6 inches, and was chambered for the .32 Long Colt (it would also accept the .32 Short Colt), .32 Colt New Police, and .38 Colt New Police cartridges. Checkered Walnut grips became standard after 1923. The Second issue began in 1928 and ran until 1947, adding a somewhat heavier frame as well as a serrated topstrap to reduce sight glare, while retaining the wooden grips. Both of Colt's “New Police” rounds were actually slight redesigns of existing S&W cartridges, the .32 S&W Long and .38 S&W with the bullet noses flattened, as Colt resisted providing its main competitor with any free advertising. Colt's Positive Lock safety, the innovation responsible for the gun's introduction, functioned by preventing the firing pin from striking the primer of the cartridge unless the trigger was deliberately pulled. Intended to address deficiencies of earlier models such as the Single Action Army, the Positive Lock prevented an accidental discharge even if the hammer was struck or the pistol was dropped, allowing the revolver to be safely carried with all six chambers loaded. The revolver’s sights consisted of a half-moon blade front with a fixed iron open rear sight, which was a simple V-notch shaped groove milled into the revolver’s topstrap.
Police Positive Target
Weighing 22 ounces and available with a blued finish and black hard rubber grips in .22 Long Rifle, .22 WRF, .32 Long (and Short) Colt, and .32 Colt New Police (.32 S&W Long) chamberings, the First issue of this model featured an adjustable open iron sighted 6 inch barrel and was marketed from 1910 to 1925, with checked Walnut grips replacing the rubber ones after 1923. A Second issue was sold from 1926 to 1941 and differed from the First in that it had a slightly heftier frame which upped the weight to 26 ounces; also Colt’s nickel finish was offered as an option. In today's collectable market, the .32 New Police version appears to be the most sought after and valuable.
Police Positive Special
The Colt Police Positive Special was an iterative improvement of Colt's earlier Police Positive model, the only differences being a slightly lengthened cylinder and elongated and strengthened frame to allow the chambering of the longer, more powerful .32-20 Winchester and .38 Special cartridges. (Full article at link)
- Hong Kong: Former standard issue sidearm of Hong Kong Police Force, replaced by Smith & Wesson Model 10
- “Colt Police Positive” Bellum Web site. Accessed September 16, 2008.
- Shideler, Dan. “Nobody Wants This Colt”, Gun Digest magazine Web site. Accessed September 16, 2008.
- Lark, Syd. “Colt .38 Police Positive”, All Experts Web site. Accessed September 16, 2008.
- Scarlata, Paul. “Colt's Official Police Revolver”, Shooting Times magazine Web site – Handgun Reviews. Accessed August 13, 2008.
- "COLT'S MANUFACTURING COMPANY, INC. REVOLVERS: DOUBLE ACTION, SWING OUT CYLINDER", Cheaper Than Dirt Web site. Accessed September 22, 2008.
- Cumpston, Mike. “.32 Colt Police Positive Special” Archived September 11, 2016, at the Wayback Machine., Gunblast Webzine. Accessed September 11, 2008.
- The Colt Revolver in the American West—Police Positive .22 Target Model G
- The Colt Revolver in the American West—Cutaway Police Positive .38 Model