Clock-face scheduling

Example of integrated timetables between interregional and regional services on the Swiss network. The two trains are programmed to meet in the hub of Geneva around 15:30 and also share a platform to minimise transfer times.

A clock-face schedule or cyclic schedule is a timetable in which public means of transport run in consistent intervals, as opposed to timetable that is purely driven by demand and with irregular headways. By extension, extension programs lines to converge on hubs at a given point of the clock-face. The goal of clock-face schedules is to increase the attractiveness and versatility of public transport. They are easier to memorize for passengers since the departure times repeat. A constant schedule over the whole day can also improve service during off-peak hours. They can be attractive for transportation companies since the repeating pattern makes more efficient use of personnel, infrastructure and vehicles and also makes resource planning easier.

Regular timetables were first developed at the end of the 19th century, for local public transport, such as trams, rapid transit, and trains in the vicinity of large cities like New York City. A clock-face schedule currently is used in the New York City Subway system; the London Underground; Merseyrail's Northern and Wirral lines; and metropolitan transit. Its name comes from the fact that departures take place when the minute hand is at the same place every hour: 6:15, 7:15, 8:15 etc.

Line-based

Each line can have an individual regular schedule, without connections to other lines. Even then, it may be necessary to coordinate different means of transport if the mode of transport changes, like at the terminal stop of a tram network, if the line continues by bus. That may, however, cause passengers to have to wait at the transfer point for any number of minutes until the next bus or train comes along.

The timetables may be attractive even if they provide no connections to other public transport, as they allow a continuous use of vehicles and personnel.

Line-bound regular timetables are especially useful for lines with high service frequencies. If vehicles with the same destination follow each other in short intervals, transfer times are short even if there are delays. However, if the service intervals are 20 minutes or longer, lines should usually be co-ordinated. One simple way of doing that is to shift the departure times of one of the lines to match the other.

Network-based

Buses meet in Herford, Alter Markt

An integrated schedule is a clock-face schedule that covers not just some lines but the whole area served by possibly several different means of public transport. A characteristic of integrated regular timetables is that there is more than one central hub. It applies the hub-and-spoke concept to the whole transport network.

Having several lines meet at hubs with vehicles of all lines arriving and leaving at the same time is a modern way of connecting multiple lines. Usually, all lines wait for a delayed vehicle. The goal is to reduce transfer times to a few minutes, with a default time of five minutes. However, in actual operation this time span is often larger due to vehicles being early or late, high passenger volume (such as rush hour) or assisting passengers with disabilities. The waiting times at such transfer stops the through service on a line can become unattractive and cause the rest of the lines to be late for the next loop.

Examples of such networks are often nighttime and city bus networks. The connections are optimized only within the network, but not for transfers to rail or intercity bus lines. Such concepts need purpose-built stations, which can handle high passenger volumes. The space constraints within cities can be a reason to use other concepts.

An integrated regular timetable needs routes that take 28 or 58 minutes for a vehicle to make it from one hub to another in time. In contrast, a route that takes 40 minutes would be bad because vehicles and possibly passengers would have to wait uselessly for their connections. Thus, a route that takes 40 minutes generates nearly the same cost as a route that takes 58 minutes, as vehicles and personnel cannot be used in the remaining 20 minutes. Therefore, lines are often cut or extended to meet that requirement when an integrated timetable is introduced.

Emergence of integrated timetables

The first integrated regular timetables were developed for railways. After the successful introduction of a line-bound regular timetable on one line in Switzerland in 1968,[1] the development continued in the Netherlands. In 1970 and 1971, Nederlandse Spoorwegen introduced a regular timetable with multiple hubs. In Germany, the first large-scale use of regular timetables was the InterCity network of 1979, which provided hourly long-distance services between cities. In 1982, a nationwide integrated regular timetable was introduced in Switzerland, which covered all but a few railway and bus lines. The base frequency was once an hour. The system was improved every two years and resulted in the Rail 2000 project of Swiss Federal Railways.

A regional bus service meets an interregional train service at Leuk (Switzerland) train station

Switzerland

Services on the Swiss railway network are integrated with one another and with other forms of public transport. Unlike its larger European neighbors, compact Switzerland has not developed a comprehensive high-speed rail network,[2] with the running speed on its few stretches[3] of relatively high-speed line being 200 km/h (124 mph).[4] Instead, the priority is not so much the speeding up of trains between cities but the reduction of connection times throughout the nodal system.[5] Swiss Federal Railways have adapted their infrastructure in such a way that journey times on main lines between hubs are multiples of 30 minutes so that on the hour or half-hour, all trains stand in the main stations at the same time, thus minimising connection times. Indeed, the above-mentioned Mattstetten–Rothrist line reduces journey times from Bern to Zurich from 72 minutes to 56 minutes[6] in keeping with the clock-face scheduling.[7]

However, on some single tracked lines the timetables may be 30/30 or 60/60 minutes, with the actual timetables being asymmetrical (such as 20/40 minutes), as the passing loops are not positioned ideally, or alternate connections at either ends have to be reached.

Germany

Since 1990, most of the states of Germany have introduced integrated timetables for short-distance public transport, running hourly or every two hours, such as Allgäu-Schwaben-Takt in 1993, Rheinland-Pfalz-Takt in 1994 and NRW-Takt in 1998. Transport associations have introduced regular timetables with base frequencies of 20 or 30 minutes, which are partially changed to 10 or 5 or even 15 or 7.5 minutes by overlaying multiple lines. In some areas, local buses are also integrated; RegioTakt in NRW and in parts of Lower Saxony.

These developments have led to "integrated timetable islands", which all adhere to the Germany-wide symmetry minute (58½), which is used also in Switzerland and partially in other European Countries. Major problems exist in regions where transport associations of different states interact (like at Osnabrück). In order to introduce a Germany-wide integrated regular timetable, the alliance "Deutschland-Takt" was founded in 2008. Its goal is to start a discussion about a better system for public transport in Germany and to highlight room for improvement.[8] The Bundesarbeitsgemeinschaft Schienenpersonennahverkehr (BAG-SPNV) and Deutsche Bahn AG are currently conducting feasibility studies for a Germany-wide integrated timetable.[9]

References

External links

This article is issued from Wikipedia - version of the 10/27/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.