Finger vibrato

Finger vibrato is vibrato produced on a string instrument by cyclic hand movements. Despite the name, normally the entire hand moves, and sometimes the entire upper arm. It can also refer to vibrato on some woodwind instruments, achieved by lowering one or more fingers over one of the uncovered holes in a trill-like manner. This flattens the note periodically creating the vibrato.


There are three types of violin vibrato: finger, wrist, and full-arm. In finger vibrato, the performer only moves his/her fingers; in full-arm, the performer pulls his/her arm back and forth on the violin but only minimally changes his/her finger's position, creating a change of tone.

Throughout the 20th century, finger vibrato was normally used in playing all members of the violin family unless otherwise indicated. Toward the end of the century, playing without vibrato became a more accepted technique in certain contexts.


In its pure form, vibrato is usually achieved by twisting the wrist rapidly to bend the note slightly, moving to and from the root note. The speed of the vibrato oftentimes has a great effect on the way the note is perceived, with faster vibratos commonly adding tension and stress, while slower vibratos produce a more lyrical sound. The slowest of vibratos can be used to imitate a bowed instrument "growing" a note after its initial inception. Even though this effect refers to volume in bowed instruments, having a pitch variation that follows the same structure of the volume variation in many situations can have the same effect for the listeners.

In contemporary music, finger vibrato is also routinely used by classical guitarists on longer notes, to create an impression of a longer sustain. The technique is also used by jazz bassists to add depth of tone.

Axial pitch-shifting

Axial vibrato is produced by moving a stopped (held-down) string with the left hand in a direction parallel to its axis, which increases or reduces the tension on the string and thereby alters the pitch. This type of vibrato is typically used by classical guitarists (see Classical guitar technique), but can be performed on any kind of guitar, and is frequently used on steel string and electric guitars. When a classical guitarist sees the term vibrato written in a score, this is generally the first effect that comes to mind. [1]

Radial pitch-shifting (string bending)

Example of bending on electric guitar
whole tone on electric guitar

Radial pitch-shifting (also referred to as "string bending" or "bending") is produced by moving the stopped (held-down) string with the fretting hand in a direction perpendicular to its axis and parallel to the frets. This type of pitch-shifting is associated with blues, rock, country and pop music.[2] The effect generally shifts the pitch over a wider range than axial pitch-shifting. It can produce vibrato as a cyclic variation in pitch, a single up-and-down swoop, or as a shift from one pitch to another that is then held. If the strings and action of the guitar are light enough, a player can bend notes by a semitone or more—so string bending can be a way of making a portamento transition between notes, and not just as a decoration on a note. String bends are one of the few ways to achieve microtonality, especially blue notes, on the guitar.

Basic technique

To produce a bend, the guitarist puts a finger on the string and then, while pressing the string down to the fingerboard, strikes a tone, and pushes or pulls the string to the side. This has the effect of stretching the string and thus makes its pitch higher. Generally a bend on the lower (6th–4th) strings moves them down vertically, as seen from the guitarist's point of view, and a bend on the higher (3rd–1st) strings moves them up. The technique can also be used with pinch harmonics to make "squealies".

A backward, reverse or release bend involves pressing the string to the fingerboard, pulling or pushing it up to stretch the string first, then striking the string and relaxing the string to normal position. This causes the note to go flat, the reverse direction of straight bend.

Sometimes a guitarist bends a note on a certain string up, while playing the note the string is being bent to on another string, creating a unison bend.[3]

Bends of one or two semitones are the most common, but skilled players may use bends from three semitones to as many as five or more semitones,[2] as can be heard in the solo played by David Gilmour on the song "Another Brick In the Wall Pt.2" from Pink Floyd's album The Wall. In addition to the player's skill, the range of a pitch bend is limited to some extent by the type of guitar, material and stiffness of the strings, and area of the neck where the bends are played. For example, steel strings bend further in pitch than nylon strings, thin strings further than thick strings, bends in the middle of the neck further than bends near the nut, etc.

In blues playing, the target note can be slightly higher or lower than the fretted note one or two frets higher. It can be a quarter tone or not even exactly that, but a pitch not present in the tempered scale, being a natural third or seventh instead (or close to it). These are the blue notes, one of which is, for example, between the minor and major third of the scale. The exact location varies from performer to performer.


Behind-the-nut pitch-shifting

Also known as "Behind-the-nut bending"

Press the string between the nut and the machine head (tuning key), and the pitch shifts.

The particular advantage of this technique is that unstopped notes can be pitch-shifted (bent).



When a string is bent, the sound it creates is much smoother than would be otherwise, even using other legato techniques such as hammer-ons, pull-offs, or finger slides. String bending on the guitar was first used in blues to mimic the smooth sound of a slide guitar. It has since become an integral part of playing lead guitar. Some masters of string bending on guitar include David Gilmour, Tony Iommi, Brian May, T-Bone Walker, B. B. King, and Eric Clapton, as well as many other blues, country, and jazz-influenced guitarists. To facilitate his extensive string bending, Clapton used to substitute an unwound banjo string for the third string on his guitar. At that time, no set of light-gauge strings with an unwound third string was available.

A note is pre-bent up one semitone, then bent back, followed with a one-tone pull down and hand vibrato.

Problems playing this file? See media help.

Keyboard instruments

Finger vibrato is also a standard part of clavichord technique, known as Bebung.

Until the first half of the 20th century, the clavichord was the only keyboard instrument on which finger vibrato was possible. In 1928, Maurice Martenot—inspired by his experience as a cellist—invented the Ondes Martenot, which featured a keyboard that the player could rock back and forth laterally.

Other finger vibrato techniques may also be used on pressure-sensitive electronic keyboards with appropriate sounds and patches. For example, some Rodgers digital church organs have an optional voice for the upper keyboard that provides a solo trumpet with velocity-sensitive volume and pressure-sensitive pitch, so a skilled player can play a realistic trumpet solo.

Wind instruments

Finger vibrato is used on several woodwind instruments, in both classical and traditional music. In Baroque music, it was called flattement in French and used, usually on long notes, on the Baroque flute and recorder, and noted in the writings of Jacques-Martin Hotteterre and Michel Corrette. In Irish music, it is used on the uillean pipes and pennywhistle. In contemporary terms this technique is more usually referred to as a "timbral trill".

See also


  1. Classical Guitar Vibrato Explained
  2. 1 2 "A Couple Guitar Tips". How To Play Blues Guitar. 2008-07-30. Retrieved 2008-07-31.
  3. Unison bends

External links

This article is issued from Wikipedia - version of the 11/23/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.