Audio and video interfaces and connectors

Audio connectors and video connectors are electrical connectors (or optical connectors) - plugs and sockets - for carrying audio signal and video signal.

Audio interfaces and video interfaces define physical parameters and interpretation of signals. For digital audio and digital video, this can be thought of as defining the physical layer, data link layer, and most or all of the application layer. For analog audio and analog video these functions are all represented in a single signal specification like NTSC or the direct speaker-driving signal of analog audio. Physical characteristics of the electrical or optical equipment includes the types and numbers of wires required, voltages, frequencies, optical intensity, and the physical design of the connectors. Any data link layer details define how application data is encapsulated (for example for synchronization or error-correction). Application layer details define the actual audio or video format being transmitted, often incorporating a codecs not specific to the interface, such as PCM, MPEG-2, or the DTS Coherent Acoustics codec. In some cases, the application layer is left open; for example, HDMI contains an Ethernet channel for general data transmission.

Some types of connectors are used by multiple hardware interfaces; for example, RCA connectors are defined both by the composite video and component video interfaces, but DVI is the only interface that uses the DVI connector. This means that in some cases not all components with physically compatible connectors will actually work together.

Some of these connectors, and other types of connectors, are also used at radio frequency (RF) to connect a radio or television receiver to an antenna or to a cable system; RF connector applications are not further described here. Analog A/V connectors often use shielded cables to inhibit radio frequency interference (RFI) and noise.

For efficiency and simplicity, the same codec or signal convention is used by the storage medium. For example, VHS tapes can store a magnetic representation of an NTSC signal, and the specification for Bluray discs incorporates PCM, MPEG-2, and DTS. Some playback devices can re-encode audio or video so that the format used for storage does not have to be the same as the format transmitted over the A/V interface (which is helpful if a projector or monitor cannot handle a newer codec).

Interfaces and their connectors

Interface Connectors
Audio or Video Digital or Analog Description
Audio Only Analog Often unmarked on consumer audio equipment since it is so common, or labelled with headphones symbol or as "line out". Computers and other equipment sometimes use Microsoft-Intel color coding scheme, especially when there are multiple input/output plugs. 3.5 mm TRS minijack
Balanced audio 6.35 mm TRS audio jack (shielded twisted pair),
XLR (shielded twisted pair)
Digital S/PDIF (Sony/Philips Digital Interconnect Format). Via Coaxial or Optical cables. RCA Jack (Coaxial),
TOSLINK (Optical),
BNC (Rare)
AES3 (also known as AES/EBU) RCA Jack (Coaxial),
XLR (shielded twisted pair),
TOSLINK (Optical),
BNC
Video Only Analog Video Graphics Array (VGA) D-subminiature 15 pin
Composite. Often designated by the CVBS acronym, meaning "Color, Video, Blank and Sync". RCA jack, normally yellow (often accompanied with red and white for right and left audio channels respectively)
S-Video aka Separate Video. Carries standard definition video and does not carry audio on the same cable. Mini-DIN 4 Pin
Component. In popular use, it refers to a type of analog video information that is transmitted or stored as three separate signals. Either RGB interfaces or YPbPr 3 RCA Jacks
Composite, S-Video, and Component VIVO = Mini-DIN 9 Pin with breakout cable.
Digital And Analog Digital Visual Interface (DVI) DVI connector
Video and Audio Analog SCART (Peritel) SCART
Digital High-Definition Multimedia Interface (HDMI),BNC HDMI connector
DisplayPort DisplayPort connector
HDBaseT 8P8C connector
IEEE 1394 "FireWire" FireWire or i.LINK connectors

Multiple signals

Some connectors can carry both audio and video signals simultaneously:

Other composite connectors that carry video, audio, power, and USB:

S/PDIF

The electrical coaxial cable (with RCA jacks) or optical fibre (TOSLINK).

Note that there are no differences in the signals transmitted over optical or coaxial S/PDIF connectors—both carry exactly the same information. Selection of one over the other rests mainly on the availability of appropriate connectors on the chosen equipment and the preference and convenience of the user. Connections longer than 6 meters or so, or those requiring tight bends, should use coaxial cable, since the high light signal attenuation of TOSLINK cables limits its effective range.

HDMI

HDMI Type A socket

High-Definition Multimedia Interface (HDMI) is a compact audio/video standard for transmitting uncompressed digital data.

There are three HDMI connector types. Type A and Type B were defined by the HDMI 1.0 specification. Type C was defined by the HDMI 1.3 specification.

Type A is electrically compatible with single link DVI-D. Type B is electrically compatible with dual link DVI-D but has not yet been used in any products.

IEEE 1394 "FireWire"

The 6-circuit and 4-circuit alpha FireWire 400 connectors

IEEE 1394 FireWire is a digital data transfer protocol commonly used for digital cameras (common on MiniDV tape camcorders), but also used for computer data and audio data transfers. In the United States, cable TV converter set top boxes by law[1] also have the connection for transferring content directly to a TV (if equipped with a port) or computer for viewing. 1394 can also use coaxial cable as a medium for longer runs.

Unlike Point-to-Point connections listed above, IEEE 1394 is able to host several signals on the same wire, with the data delivered and shown on the destination set. It is also fully bi-directional, with its full bandwidth used in one direction or the other, or split directions up to its maximum.[2]

DisplayPort

DisplayPort is a digital display interface standard (approved May 2006, current version 1.4 published on March 1 2016). It defines a new license-free, royalty-free, digital audio/video interconnect, intended to be used primarily between a computer and its display monitor, or a computer and a home-theater system.

The video signal is not compatible with DVI or HDMI, but a DisplayPort connector can pass these signals through. DisplayPort is a competitor to the HDMI connector, the de facto digital connection for high-definition consumer electronics devices.

Combined audio/video interfaces

Some connectors can carry both audio and video signals simultaneously:

Other composite connectors that carry video, audio, power, and USB:

Audio connectors

Audio connectors are used for audio frequencies. They can be analog or digital.

Single-wire connectors used frequently for analog audio include:

Phone connector

2.5 mm (3/32") mono (TS), 3.5 mm (1/8") mono and stereo (TRS), and 6.3 mm (1/4") stereo (TRS) phone connectors

A phone connector (tip, ring, sleeve) also called an audio jack, phone plug, jack plug, stereo plug, mini-jack, or mini-stereo. This includes the original 6.35mm (quarter inch) jack and the more recent 3.5mm (miniature or 1/8 inch) and 2.5mm (subminiature) jacks, both mono and stereo versions.

DIN

Five-pin male 180° DIN connector

A DIN connector is a connector that was originally standardized by the Deutsches Institut für Normung (DIN). Mini-DIN is a variation.

BNC

Male 50 ohm BNC connector

The BNC (Bayonet Neill Concelman) connector is a very common type of RF connector used for terminating coaxial cable.

TOSLINK

Clear TOSLINK cable with a round connector

TOSLINK or Optical Cable is a standardized optical fiber connection system.

XLR

XLR3 cable connectors, female on left and male on right

XLR connector plugs and sockets are used mostly in professional audio and video electronics cabling applications. XLR connector are also known as Cannon plugs after their original manufacturer. They are used for analog or digital balanced audio with a balanced line

Digital audio interfaces and interconnects with the AES/EBU interface also normally use an XLR connector.

RCA

RCA Plugs for composite video (yellow) and stereo audio (white and red)

RCA connectors, also known as phono connectors or phono plugs, are used for analog or digital audio or analog video. These were first used inside pre-World-War-II radio-phonographs to connect the turntable pickup to the radio chassis. They were not intended to be disconnected and reconnected frequently, and their retaining friction was quite sufficient for their original purpose. Furthermore, the design of both cable and chassis connectors was for minimum cost. Initially intended for audio frequency connections only, the RCA plug was also used for analog composite video and non-critical radio-frequency applications.

Video connectors

Video connectors carry only video signals. Common video-only connectors include:

Mini-DIN

mini-DIN 4 pin for S-Video

The Mini-DIN connectors are a family of multi-pin electrical connectors used in a variety of applications. Mini-DIN is similar to the larger, older DIN connector. Both are standards of the Deutsches Institut für Normung, the German standards body.

D-subminiature

DA, DB, DC, DD, and DE sized connectors

D-subminiature or D-sub is a common type of electrical connector used particularly in computers. Calling them "subminiature" was appropriate when they were first introduced, but today they are among the largest common connectors used in computers. The DB25 is used for multi-track recording and other multi-channel audio, analog or digital (ADAT interface (DB25)).

Video In Video Out

A graphics card with VGA, VIVO and DVI outputs
A 6-connector VIVO splitter cable. From left to right: S-Video In, Component Pb out, Component Pr out, Component Y out/Composite out, Composite in, S-Video Out

Video In Video Out, usually seen as the acronym VIVO (commonly pronounced vee-voh), is a graphics card port which enables some video cards to have bidirectional (input and output) video transfer through a Mini-DIN, usually of the 9-pin variety, and a specialised splitter cable (which can sometimes also transfer sound).

VIVO is found predominantly on high-end ATI video cards, although a few high-end NVIDIA video cards also have this port. VIVO on these graphics cards typically supports Composite, S-Video, and Component as outputs, and composite and S-Video as inputs. Many other video cards only support component and/or S-Video outputs to complement Video Graphics Array or DVI, typically using a component breakout cable and an S-Video cable.

DVI Connector

Male DVI connector pins (view of plug)
Male M1-DA connector pins (view of plug)

The Digital Visual Interface (DVI) is a video interface standard designed to maximize the visual quality of digital display devices such as flat panel LCD computer displays and digital projectors. It is designed for carrying uncompressed digital video data to a display.

There are four basic connectors:

  • DVI-D (digital only)
  • DVI-A (analog only)
  • DVI-I (integrated, digital & analog)
  • M1-DA (integrated, digital, analog & USB)

The connector also includes provision for a second data link for high resolution displays, though many devices do not implement this. In those that do, the connector is sometimes referred to as DVI-DL (dual link).

So we need to know two things about the connector:

  1. Whether it carries analog, digital, or both; and
  2. For connectors that carry digital links, if it is single or dual link, and if it carries USB

Color codes

Audio

white RCA/TS analogue audio, left channel;
also mono (RCA/TS), stereo (TRS only),
or undefined/other
black RCA/TS/TRS
grey RCA/TS/TRS
red RCA/TS analogue audio, right channel
orange RCA S/PDIF digital audio

For computers:

green TRS 3.5mm stereo output, front channels
black TRS 3.5mm stereo output, rear channels
grey TRS 3.5mm stereo output, side channels
gold TRS 3.5mm dual output, center and subwoofer
blue TRS 3.5mm stereo input, line level
pink TRS† 3.5mm mono microphone input

† Although the mic input is usually mono, the input is still a TRS phone socket. Many mono 'computer' mics are fitted with TRS plugs. The tip is for the MIC and the ring is for power (to power an electret-condenser style MIC).

There are exceptions to the above:

PC System Design Guide audio

Older sound cards had no common standard color codes until after PC 99. The PC System Design Guide (also known as the PC 97, PC 98, PC 99, or PC 2001 specification) is a series of hardware design requirements and recommendations for IBM PC compatible personal computers, compiled by Microsoft and Intel Corporation during 1997–2001. PC 99 introduced a color code for the various standard types of plugs and connectors used on PCs.

The color codes for audio plugs follow:[4]

Orange TRS 3.5 mm Output, subwoofer
Blue TRS 3.5 mm Input, line level
Pink TRS† 3.5 mm microphone input
Lime TRS 3.5 mm Output, front channels
Brown TRS 3.5 mm Output, 'Right-to-left speaker'
Gold TRS 3.5 mm MIDI/game

† Though the input is often mono, the actual connector is usually still a 3-conductor TRS phone minijack. Many mono computer microphones have 3-conductor TRS plugs.

Video

yellow RCA/BNC composite video
red RCA/BNC red or Pr/Cr chrominance
green RCA/BNC green or luminance
blue RCA/BNC blue or Pb/Cb chrominance
white BNC horizontal sync
black BNC vertical sync

Newer connectors are identified by their shape and not their colour.

See also

References

  1. http://www.1394ta.org/consumers/FCC_complaint.html All Cable TV box have working 1394 ports, FCC rule CS Docket 97-80" and "section 47 C.F.R. 76.640(b)(4)
  2. "Archived copy" (PDF). Archived from the original (PDF) on 2011-06-06. Retrieved 2010-06-04. Demonstrating the multi-device capabilities of IEEE A/V network.
  3. 2.5mm Audio Cables Archived September 26, 2013, at the Wayback Machine.
  4. PC 99 System Design Guide, Intel Corporation and Microsoft Corporation, 14 July 1999. Chapter 3: PC 99 basic requirements (PC 99 System Design Guide (Self extracting .exe). Requirement 3.18.3: Systems use a color-coding scheme for connectors and ports. Accessed 2009-02-05
This article is issued from Wikipedia - version of the 11/14/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.