Seismic source

This article is about artificial seismic sources. For natural seismic sources, see earthquake, volcano, and related articles.
An air gun seismic source (30 litre)

A seismic source is a device that generates controlled seismic energy used to perform both reflection and refraction seismic surveys. A seismic source can be simple, such as dynamite, or it can use more sophisticated technology, such as a specialized air gun. Seismic sources can provide single pulses or continuous sweeps of energy, generating seismic waves, which travel through a medium such as water or layers of rocks. Some of the waves then reflect and refract and are recorded by receivers, such as geophones or hydrophones.[1]

Seismic sources may be used to investigate shallow subsoil structure, for engineering site characterization, or to study deeper structures, either in the search for petroleum and mineral deposits, or to map subsurface faults or for other scientific investigations. The returning signals from the sources are detected by seismic sensors (geophones or hydrophones) in known locations relative to the position of the source. The recorded signals are then subjected to specialist processing and interpretation to yield comprehensible information about the subsurface.[2]

Source model

A seismic source signal has the following characteristics:

  1. Generates an impulse signal
  2. Band-limited
  3. The generated waves are time-varying

The generalized equation that shows all above properties is:

where is the maximum frequency component of the generated waveform.[3]

Types of sources

Explosives

Explosives, such as dynamite, can be used as crude but effective sources of seismic energy. For instance, hexanitrostilbene was the main explosive fill in the thumper mortar round canisters used as part of the Apollo Lunar Active Seismic Experiments.[4] Generally, the explosive charges are placed between 6 and 76 metres (20 and 250 ft) below ground, in a hole that is drilled with dedicated drilling equipment for this purpose. This type of seismic drilling is often referred to as "Shot Hole Drilling". A common drill rig used for "Shot Hole Drilling" is the ARDCO C-1000 drill mounted on an ARDCO K 4X4 buggy. These drill rigs often use water or air to assist the drilling.

Air gun

An air gun is used for marine reflection and refraction surveys. It consists of one or more pneumatic chambers that are pressurized with compressed air at pressures from 14 to 21 MPa (2,000 to 3,000 psi). Air guns are submerged below the water surface, and towed behind a ship. When an air gun is fired, a solenoid is triggered, which releases air into a fire chamber which in turn causes a piston to move, thereby allowing the air to escape the main chamber and producing a pulse of acoustic energy.[5] Air gun arrays may consist of up to 48 individual air guns with different size chambers, fired in concert, the aim being to create the optimum initial shock wave followed by the minimum reverberation of the air bubble(s).

Air guns are made from the highest grades of corrosion resistant stainless steel. Large chambers (i.e., greater than 1.15 L or 70 cu in) tend to give low frequency signals, and the small chambers (less than 70 cubic inches) give higher frequency signals.

Plasma sound source

Plasma sound source fired in small swimming pool

A plasma sound source (PSS), otherwise called a spark gap sound source, or simply a sparker, is a means of making a very low frequency sonar pulse underwater. For each firing, electric charge is stored in a large high-voltage bank of capacitors, and then released in an arc across electrodes in the water. The underwater spark discharge produces a high-pressure plasma and vapor bubble, which expands and collapses, making a loud sound.[6] Most of the sound produced is between 20 and 200 Hz, useful for both seismic and sonar applications.

There are also plans to use PSS as a non-lethal weapon against submerged divers.

Thumper truck

Thumper trucks, Noble Energy, northern Nevada 2012.

In 1953, the weight dropping Thumper technique was introduced as an alternative to dynamite sources.

Vibroseis
Vibroseis 2

A thumper truck (or weight-drop) truck is a vehicle-mounted ground impact system which can be used to provide a seismic source. A heavy weight is raised by a hoist at the back of the truck and dropped, generally about three meters, to impact (or "thump") the ground.[7] To augment the signal, the weight may be dropped more than once at the same spot, the signal may also be increased by thumping at several nearby places in an array whose dimensions may be chosen to enhance the seismic signal by spatial filtering.

More advanced Thumpers use a technology called "Accelerated Weight Drop" (AWD), where a high pressure gas (min 6.9 MPa (1,000 psi)) is used to accelerate a heavy weight Hammer (5,000 kg) to hit a base plate coupled to the ground from a distance of 2 to 3 m. Several thumps are stacked to enhance signal to noise ratio. AWD allows both more energy and more control of the source than gravitational weight-drop, providing better depth penetration, control of signal frequency content.

Thumping may be less damaging to the environment than firing explosives in shot-holes, though a heavily thumped seismic line with transverse ridges every few meters might create long-lasting disturbance of the soil. An advantage of the thumper (later shared with Vibroseis), especially in politically unstable areas, is that no explosives are required.

Electromagnetic Pulse Energy Source (Non-Explosive)

EMP sources based on the electrodynamic and electromagnetic principles.

Seismic vibrator

A Seismic vibrator propagates energy signals into the Earth over an extended period of time as opposed to the near instantaneous energy provided by impulsive sources. The data recorded in this way must be correlated to convert the extended source signal into an impulse. The source signal using this method was originally generated by a servo-controlled hydraulic vibrator or shaker unit mounted on a mobile base unit, but electro-mechanical versions have also been developed.

The "Vibroseis" exploration technique was developed by the Continental Oil Company (Conoco) during the 1950s and was a trademark until the company's patent lapsed.

Boomer sources

Boomer sound sources are used for shallow water seismic surveys, mostly for engineering survey applications. Boomers are towed in a floating sled behind a survey vessel. Similar to the plasma source, a boomer source stores energy in capacitors, but it discharges through a flat spiral coil instead of generating a spark. A copper plate adjacent to the coil flexes away from the coil as the capacitors are discharged. This flexing is transmitted into the water as the seismic pulse.[8]

Originally the storage capacitors were placed in a steel container (the bang box) on the survey vessel. The high voltages used, typically 3,000 V, required heavy cables and strong safety containers. Recently, low voltage boomers have become available.[9] These use capacitors on the towed sled, allowing efficient energy recovery, lower voltage power supplies and lighter cables. The low voltage systems are generally easier to deploy and have fewer safety concerns.

Noise sources

Correlation-based processing techniques also enable seismologists to image the interior of the Earth at multiple scales using natural (e.g., the oceanic microseism) or artificial (e.g., urban) background noise as a seismic source.[10] For example, under ideal conditions of uniform seismic illumination, the correlation of the noise signals between two seismographs provides an estimate of the bidirectional seismic impulse response.

See also

References

  1. R.E. Sheriff (2002) p160 & p 182
  2. R.E. Sheriff (2002) p312
  3. Seismic Wave Propagation Modeling and Inversion, Phil Bording
  4. NASA reference publication
  5. R.E. Sheriff (2002) p6-8
  6. R.E. Sheriff (2002) p328
  7. R.E. Sheriff (2002) p357
  8. Sheriff R. E., 1991, Encyclopedic Dictionary of Exploration Geophysics, Society of Exploration Geophysicists, Tulsa, 376p
  9. Jopling J. M., Forster P. D., Holland D. C. and Hale R. E., 2004, Low Voltage Seismic Sound Source, US Patent No 6771565
  10. R.E. Sheriff (2002) p295

Bibliography


This article is issued from Wikipedia - version of the 11/30/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.