Adaptive beamformer

An adaptive beamformer is a system that performs adaptive spatial signal processing with an array of transmitters or receivers. The signals are combined in a manner which increases the signal strength to/from a chosen direction. Signals to/from other directions are combined in a benign or destructive manner, resulting in degradation of the signal to/from the undesired direction. This technique is used in both radio frequency and acoustic arrays, and provides for directional sensitivity without physically moving an array of receivers or transmitters.

Motivation/Applications

Adaptive beamforming was initially developed in the 1960s for the military applications of sonar and radar.[1] There exist several modern applications for beamforming, one of the most visible applications being commercial wireless networks such as LTE. Initial applications of adaptive beamforming were largely focused in radar and electronic countermeasures to mitigate the effect of signal jamming in the military domain.[2]

Basic Concepts

An adaptive beamforming system relies on principals of wave propagation and phase relationships. See Constructive interference, and Beamforming. Using the principles of superimposing waves, a higher or lower amplitude wave is created (e.g. by delaying and weighting the signal received). The adaptive beamforming system dynamically adapts in order to maximize or minimize a desired parameter, such as Signal-to-interference-plus-noise ratio.

An antenna gain pattern created by adjusting phase and magnitude of signal transmitted by Tx1, Tx2, and Tx3. Dynamically adjusting phase and magnitude will cause the antenna gain pattern to change.

Adaptive Beamforming Schemes

There are several ways to approach the beamforming design, the first approach was implemented by maximizing the signal to noise ratio (SNR) by Applebaum 1965.[4] This technique adapts the system parameters in order to maximize the receive signal power, while minimizing noise (such as interference or jamming). Another approach is the Least Mean Squares (LMS) error method implemented by Widrow, and Maximum Likelihood Method (MLM), developed in 1969 by Capon.[5] Both the Applebaum and the Widrow algorithms are very similar, and converge toward an optimal solution.[6] However, these techniques have implementation drawbacks. In 1974, Reed demonstrated a technique known as Sample-Matrix Inversion (SMI). SMI determines the adaptive antenna array weights directly, Unlike the algorithms of Applebaum and Widrow.[7]

A detailed explanation of the adaptive techniques introduced above can be found here:

See also

An array of transmitters and receivers used to illustrate the multiple signal paths from a transmitter to a receiver.

References

  1. Blogh, J. ; Hanzo, L. (2002). Third-Generation Systems and Intelligent Wireless Networking:Smart Antennas and Adaptive Modulation. Wiley-IEEE Press.
  2. Monzingo, Robert A. Miller, Thomas W. (2004). Introduction to Adaptive Arrays. SciTech Publishing.
  3. Qinghua Li; Guangjie Li; Wookbong Lee; Moon-il Lee; Mazzarese, D.; Clerckx, B.; Zexian Li (May 2010). "MIMO techniques in WiMAX and LTE: A Feature Overview". Communications Magazine, IEEE. 48 (5): 86, 92.
  4. Blogh, J. ; Hanzo, L. (2002). Third-Generation Systems and Intelligent Wireless Networking:Smart Antennas and Adaptive Modulation. Wiley-IEEE Press.
  5. Blogh, J. ; Hanzo, L. (2002). Third-Generation Systems and Intelligent Wireless Networking:Smart Antennas and Adaptive Modulation. Wiley-IEEE Press.
  6. Monzingo, Robert A. Miller, Thomas W. (2004). Introduction to Adaptive Arrays. SciTech Publishing.
  7. Blogh, J. ; Hanzo, L. (2002). Third-Generation Systems and Intelligent Wireless Networking:Smart Antennas and Adaptive Modulation. Wiley-IEEE Press.
This article is issued from Wikipedia - version of the 5/12/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.