Rotorwing-Aero 3D-RV

3D-RV
Role Autogyro
National origin United States
Manufacturer Rotorwing-Aero
Designer Monte Hoskins
First flight 1989
Status Production completed
Number built Three (1998)
Unit cost
US$100.00 (plans only, 1998)

The Rotorwing-Aero 3D-RV is an American autogyro that was designed by Monte Hoskins and produced by Rotorwing-Aero of Salt Lake City, Utah, introduced in 1989. Now out of production, when it was available the aircraft was supplied in the form of plans for amateur construction.[1]

Design and development

The 3D-RV was designed to comply with the US FAR 103 Ultralight Vehicles rules, including the category's maximum empty weight of 254 lb (115 kg). The aircraft has a standard empty weight of 250 lb (113 kg) when equipped with a Rotax 503 or Rotax 582 engine. With heavier engines it can be registered in the US Experimental - Amateur-built category.[1]

The 3D-RV features a single main rotor, a single-seat open cockpit without a windshield, tricycle landing gear with hydraulic disk brakes, plus a tail caster. The acceptable power range is 50 to 65 hp (37 to 48 kW) and the standard engines used are twin cylinder, air-cooled, two-stroke, single-ignition 50 hp (37 kW) Rotax 503 engine and the twin cylinder, liquid-cooled, two-stroke, single-ignition 64 hp (48 kW) Rotax 582 engine, mounted in pusher configuration.[1]

The aircraft fuselage is made from bolted-together aluminum tubing and welded 4130 steel tubing. Its two-bladed rotor has a diameter of 25 ft (7.6 m) and may use either manufactured metal blades or homemade Gyrotor wooden blades. The prototype was originally flown with wooden blades of 8 ft (2.4 m) each, with a 5 ft (1.5 m) hub bar, for a diameter of 21 ft (6.4 m). In this configuration the aircraft flew acceptably, but did not climb well on hot days at higher density altitudes. The minimum control speed is 10 mph (16 km/h)[1]

The initial propeller used was a 64 in (163 cm) two bladed ground adjustable unit, but the plans specify a three-bladed ground adjustable design of 56 in (142 cm) diameter.[1]

The prototype used a conventional low landing gear design, but this was later developed into a high landing gear to set the vertical center of gravity to the prob hub height to prevent longitudinal stability issues and bunt "push-over" accidents. The final design features a tall aluminium rudder.[1]

The aircraft has a typical empty weight of 250 lb (110 kg) and a gross weight of 550 lb (250 kg), giving a useful load of 300 lb (140 kg). With full fuel of 5 U.S. gallons (19 L; 4.2 imp gal) the payload for the pilot and baggage is 270 lb (120 kg).[1]

The standard day, sea level, no wind, take off roll with a 50 hp (37 kW) engine is 1,000 ft (305 m).[1]

The manufacturer estimated the construction time from the supplied plans as 400 hours.[1]

Operational history

By 1998 the company reported that 35 sets of plans had been sold and three aircraft were completed and flying.[1]

One builder reported an eight-month completion time.[1]

Specifications (3D-RV)

Data from Purdy[1]

General characteristics

Performance

See also

References

  1. 1 2 3 4 5 6 7 8 9 10 11 12 Purdy, Don: AeroCrafter - Homebuilt Aircraft Sourcebook, Fifth Edition, page 331. BAI Communications, 15 July 1998. ISBN 0-9636409-4-1

External links

This article is issued from Wikipedia - version of the 9/12/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.